Coldtub App Qrc Through Lan Cable Flowchart - COLDTUB Icekube Owner's Manual

2.10 COLDTUB App QRC Through LAN Cable
Flowchart
The following flowchart shows how to connect COLDTUB App through connecting a LAN cable to the RJ45 Port
How to Connect Your Tub To Your Network With LAN Cable
on your COLDTUBs Processor Card and the other end connected to an RJ45 Port on your Home Router.
Obtain a LAN cable with RJ45 plugs fi t-
ted both ends and long enough to reach
from your Router to the RJ45 port on the
Processor Card mounted to the Mother-
board in the Tub Pack of your Tub.
Is your Tub equipped with an EoP
Module or WIFI Extender?
NO
Connect the Ethernet cable, one end of
cable plugs into the RJ45 port on the
Processor Card & the other end plugs
into an RJ45 port on the Router.
Scroll through the Tubs Low Level Pro-
gramming (LLP) check to ensure the Tubs
Internet Protocol (IP) address.
Do youhave an IP address?
Allow 3-4 minutes for Tub to reset.
Note: .100 or .0 are false. Any other
number is fi ne.
YES
Open the COLDTUB App on your de-
vise such as your Smart Phone or tablet.
Connect to the Tub Using
the LAN bbutton on the
App.
Note: It can take up to
6-8 times for the App to fi nd the Tub
on your Network, if need be keep
pressing the reconnect button.
Connected?
YES
Your Tub is now connected to your Network
and you can control your Tub through the App.
Go to the mycoldtub.com webpage to create
an account for your Tub and to register you
Tub. Refer Flowchart How to Connect Your
Tub to the MyCOLDTUB Server.
Quick Reference Guide
As appropriate:
• Disconnect the EoP Module from the Motherboard, disconnect the Ethernet cable from
the Processor Card and remove the EoP module from your Tub pack, or
• Disconnect the WIFI Extender from the Motherboard, disconnect the Ethernet cable
YES
from the Processor Card and remove the WIFI Extender from your Tub cabinet.
Access the Tubs Low Level
Programming (LLP) through
the Topside Controller by
holding the FILTER button
down until LLP is displayed.
Reset the Tubs Breaker (Turn
NO
power off and then on again at
the circuit breaker for the Tub).
Try connecting to the Tub with
another device
Unblock router
settings.
NO
YES
Blocked?
NO Check Router fi rewall settings
for restrictions. The router
may be set to Block devices
"scanning" the network .
• Ensure the port on your
router is not
defective.
• Try another router port.
• Try another Ethernet cable.
• Try another router.
• Try another Processor Card.
The following Supportive Video Link may
also assist you with this process:
http://www.coldtub.com/support/how-to-videos/
how-to-connect-with-direct-ethernet-connection/
• Scroll through the LLP settings by pressing the FILTER
button, each time you press the fi lter button you
move to the next LLP setting, scroll through until IP is
displayed.
• St or dy will be displayed, if St is displayed press the
Up Arrow button to change to dy Dynamic.
• Press the FILTER button again to display the Tubs IP
address (Last Octec should appear).
• Continue to press the FILTER button until you have
exited the
LLP settings. At this time the Pack will save the settings.
Access the Tubs Low Level Programming (LLP)
through the Topside Controller by holding
the FILTER button down until LLP is displayed.
Scroll through the LLP settings by pressing the FILTER but-
ton, each time you press the fi lter button you move to the
next LLP setting, scroll through until IP is displayed.
• Confi rm IP is set to dy
• Press the FILTER button again to display the Tubs IP
address(Last Octec).Note: .100 or .0 are false, any other
number is fi ne.
• Continue to press the FILTER button until you have exited
the LLP settings. At this time the Pack will save the settings.
YES
Do you have an IP address?
NO
Checkis the ETHERNET light illuminatedon the
NO
Processor Card. Look directly under the RJ45 Port?
YES
Contact your Dealer for assistance
31