List of Revisions ....................4 1.1.2 Conventions in this Manual ..................4 1.1.3 Reference to Hardware ..................5 Other Relevant Documentation ..................5 DESCRIPTIONS AND DRAWINGS ................6 Description of the NXHX 51-ETM ................6 Drawings........................7 2.2.1 Block Diagram ......................7 2.2.2 Printed Circuit Board ....................8 Operating Elements ....................10 2.3.1...
NXHX51-ETM 7763. 200 Table 2: Reference to Hardware Other Relevant Documentation Besides this device description, the following documents are also relevant for the user of the NXHX 51-ETM development board: Manual Contents Document Name NXHX 51-ETM Getting Describes typical use cases of the NXHX 51-ETM Getting Started GS XX EN.pdf...
2 Descriptions and Drawings Description of the NXHX 51-ETM The NXHX 51-ETM is a development board for the netX 51 controller. It is equipped with an netX 51 and features: Host interface, usable in different interface modes: 8/16/32 bit parallel...
Page 11
Note: If you use boot mode 1, 2 or 4, set host interface mode to “Ignore host interface during boot” (see following table). NXHX 51-ETM | Development Board DOC120606HW05EN | Revision 5 | English | 2013-10 | Released | Public...
Descriptions and Drawings 27/60 LEDs The NXHX 51-ETM is equipped with the following LEDs: No. in LED naming in LED function Color Signal name device device drawing drawing RUN# (green) System Status RDY# (yellow) (yellow / green) MMIO28 COM0 (green)
28/60 3 Using external Debuggers Instead of using the onboard debugger of the NXHX 51-ETM along with the HiTOP software, an external debugger with either ETM or JTAG interface can be connected to the NXHX 51-ETM. If an ETM debugger is used, simply connect the debugger to the ETM connector (X9) of the NXHX 51- ETM.
LED 14 (PIO78) +3.3 V For the setting of the X10 jumper on the NXHX 51-ETM required for operating the NXHX-IO at the host interface see: Table 15: X10 - Setting for NXHX-IO Board at Host Interface X3 on page 15.
SD_D0 +3.3 V SD_BA1 For the setting of the X10 jumper on the NXHX 51-ETM required for operating the NXHX-SDR at the host interface see Table 16: X10 - Setting for NXHX-SDR Board at Host Interface X3 on page 15.
Page 33
Table 36: Combination of Host Mode Switches For the setting of the X10 jumper on the NXHX 51-ETM required for operating the NXHX-PHY at the host interface see Table 17: X10 - Setting for NXHX-PHY Board at Host Interface X3 on page 15.
AOI manufacturing label. For the setting of the X10 jumper on the NXHX 51-ETM required for operating the NXHX-PHY at the host interface see Table 18: X10 - Setting for NXHX-PHYSDR Board at Host Interface X3 on page 15.
35/60 4.1.5 Parallel Dual-Port Memory at Host Interface The NXHX 51-ETM can be accessed from the PC via the NXPCA-PCI Card (order number: 7902.100), using the host interface as parallel dual-port memory. Figure 9: NXHX 51-ETM Connected to NXPCA-PCI Board For the setting of the X10 jumper on the NXHX 51-ETM required for operating the NXPCA-PCI at the host interface see Table 13: X10 –...
CAB-NXPCA-PCI The CAB-NXPCA-PCI cable can be used to connect the X3 host interface of the NXHX 51-ETM (see Host Interface (X3) section on page 16) with the Hilscher NXPCA-PCI Card (see Parallel Dual-Port Memory at Host Interface section on page 35) or other host devices.
Accessories 37/60 Fieldbus and Serial Adapters/Interfaces Figure 11: NXHX 51-ETM with possible Field-Bus-Modules Fieldbus Adapter/Interface with Duo Status LED (Ready/Error). Signal Signal XMAC TX +3,3V XMAC RX PIO 4 XMAC IO 0 PIO 5 XMAC IO 1 RSTOUT n.c. Table 40: Connector to NXHX Fieldbus Adapter...
Table 31: Pin Assignment X9 ETM Connector Table 32: Ethernet RJ45 pin assignment Table 33: Pin Assignment X100 Power Supply Table 34: LEDs on the NXHX 51-ETM Table 35: System Status LED Table 36: Combination of Host Mode Switches Table 37: Technical Data CAB-NXPCA-PCI...
Page 59
Table 54: Bill of Material NXHX-PHY (7773.030 Revision 2) Table 55: Bill of Material NXHX-PHYSDR (7773.040 Revision 1) Table 56: Technical Data NXHX 51-ETM NXHX 51-ETM | Development Board DOC120606HW05EN | Revision 5 | English | 2013-10 | Released | Public...
Need help?
Do you have a question about the NXHX 51-ETM and is the answer not in the manual?
Questions and answers