SECOLink P16 Wiring Manual page 3

Intruder alarm system
Maximum load ratings and electrical characteristics
of P series control panels
Maximum long term output current of P16 control panel:
(I + I + I + I
+AUX +BELL +PGM
Maximum long term output current of P32, P64 control panel:
(I + I + I + I
+BELL +PGM
+AUX
Maximum current out of +AUX:
Maximum current out of +BELL:
Maximum current into -PGM:
Maximum current out of +PGM for P16:
Maximum current out of +PGM for P32, P64:
Maximum battery charging current:
Control panel disconnect battery when it's voltage less than:
Minimum AC voltage on 20 VAC:
Note: with ~16 V on 20 VAC max DC current generated by
control panel power supply is 0,7A.
Maximum AC voltage on 20 VAC
Note: higher than ~22 V voltage can damage control panel
Maximum voltage on +AUX, +BELL, +PGM outputs:
Minimum voltage on +AUX, +BELL, +PGM outputs:
Maximum current of fast blowing fuse used in battery circuit:
Maximum current of slow blowing fuse used in primary AC:
Maximum AC power consumption:
Use only self-tapping screws with flat
(countersunk) head (3x30 PH) to mount keypad's
plastic on the wall . Make sure the screw is screwed
completely and screw head hides in the plastic.
Other shape screws or not completely screwed
Keypad screws may touch keypad electronics and cause
damage of keypad.
Operating temperature range:
Calculated life expectancy for P series control panels at 40
ambient temperature:
Note: ambient temperature over 40
Note: poor ventilation of cabinet increase ambient temperature.
Maximum load ratings and electrical
characteristics of PWR20
Maximum long term current out of PWR20:
(I + I + I
+AUX +BELL BAT. CHARGE
Maximum current out of +AUX:
Maximum current out of +BELL:
Maximum current into -PGM1:
Maximum battery charging current:
Module disconnect battery when it's
voltage less than:
12V battery
7Ah/20HR
Live Neutral Protective
wire wire Earth wire
Fuse
L N PE
250mA
Main Protective
Earthing terminal
Primary winding: 230V AC 50Hz
Secondary winding:
Power supply
distribution board
Electrical characteristics and additional information
1,5 A )
BAT. CHARGE
2 A )
BAT. CHARGE
:
.
Keypad mounting
-20°C to +55°C
°C
°C may reduce life expectancy.
Wiring of modules in large or high security level system
2,0A
2 A )
+1A
PWR20
+2A
-0,05A
0,35A
9,5V
Black
Red
X1
BAT
~20 VAC
AC power transformer:
~
~ 20V AC 50Hz
Restoring service PIN to default value
To restore default value (0000) for service PIN, follow the steps:
disconnect control panel from 20 V AC power supply;
1,5 A
disconnect control panel from back-up battery;
make short circuit of -PGM and zone Z1;
2 A
connect control panel to 20 V AC power supply.
Now service PIN is restored to 0000 value and system with enabled service
+1 A
mode. To reset user PIN follow the steps:
+2,0 A do not block service by pressing ENT;
press arrow key to navigate in menu;
-0,3A
go to: Main Menu/Settings/Users/Edit Users/ enter 0000 /Reset PIN to
+0,5 A
default/YES
+0,9 A
+0,35 A
9,5 V
~16 V
~22 V
Live
Neutral
wire
wire
L N
+13,9 V
+12,0 V
3,15 A
Main Protective
250 mA
Earthing terminal
150 mA
System start-up with no 230V AC power
Connect 12V battery with P
series control panel by using
a BAT connector. Use the
jumper to close the shown
pins for 1 second. The
system will start operating;
however AC loss trouble will
be indicated.
12 years
Overload of +BELL or + AUX.
Battery charging on
Low battery indicator
Module address LED
+BELL COM -PGM1TMP COM CLK-I DAT-I +AUX CLK-O DAT-O
COM from Pxx
CLK from Pxx
DAT from Pxx
+12V +12V
+12V +12V
COM COM
COM COM
CLK-O CLK-O
CLK CLK
DAT-O DAT-O
DAT DAT
Module
Control Panels P16, P32, P64
20VAC
Protective
Earth wire
PE
Fuse
250mA
Jumper
Black
Red
12V battery
7Ah/20HR
Safe wiring of outdoor siren
Use other (than control panel) transformer and
rechargeable 12V 7Ah battery to power up
PWR20. In case alarm system includes PWR20 it
is recommended to wire an outdoor siren to the
PWR20 terminals +BELL, -PGM1, (-PGM2), COM
same as shown on page 2. Failure of siren's
internal battery or the siren itself will not affect
OVL
PWR20 – power supply module with bus
CHG
repeater
LOW
MOD
Repetition of system bus is a perfect solution
when some system modules (PROX8, EXTx16)
are placed outside premises or in area
protected by detectors. It is recommended to wire
to repeated (by PWR20) bus all outside proximity
readers or keypads located near to entry door.
Attempt to make a short circuit on outside module
will make no affect to system performance as
PWR20 will detect the short circuit on repeated bus
and will disconnect repeated bus from main bus.
Terminals CLK-I, DAT-I are inputs for main bus,
terminals CLK-O and DAT-O are outputs of
repeated bus. For power supply modules must use
PWR20 output +AUX.
Wiring manual
+BELL COM -PGM +PGM COM CLK DAT +AUX Z1 COM Z2
Wire
20VAC +BELL COM -PGM
not
Page 3