External/Internal Fluval Filter Installation, Use And Maintenance - Fluval Roma Instruction Manual

EXTERNAL/INTERNAL FLUVAL FILTER INSTALLATION,
USE AND MAINTENANCE
Please refer to the instruction manual of the Fluval filter. Do not attempt to set up the Fluval filter without reading
and following the instruction manual. If it is missing or unusable, contact the store or Hagen Customer Service.
FLUVAL HEATER INSTALLATION AND PREPARATION,
USE AND MAINTENANCE
Please refer to the instruction manual of the Fluval heater. Do not attempt to set up the Fluval heater without
reading and following the instruction manual. If it is missing or unusable, contact the store or Hagen Customer
Service.
LED STRIP LIGHT INSTALLATION INSTRUCTIONS
WARNING: Disconnect the plug of all electrical equipment used for the aquarium, before placing your
hands in aquarium water and/or performing any maintenance of any kind.
Features and tips
Access Lids
The canopies are equipped with 2 Access Lids (3 for Venezia 350). This allows easy access to your aquarium.
Optional Extra for Roma Aquariums: Opening for Nutrafin Profeed Fish Feeder
A replacement canopy rear lid is available including an opening
for the use of a Nutrafin Profeed Fish-Feeder. Pull to remove the
plastic plug and access the compartment. To close, press the
plastic plug in its place. (Visit the replacement parts section on
www.hagen.com for order codes).
Initial start-up
1. Carefully place the LED Strip Light (C) on the runner of the top frame in the final position (Pict. 8)
2. Hook up the lighting unit to the LED driver with its connector. Pict. 9 also shows the connection of 2 lighting
units to a single LED driver as required by Venezia 350 only, via splitter.
3. Place the aluminium beam (B2) and the front and rear access lids (B1) on the aquarium top frame (Pict. 10).
Venezia 350 features 2 aluminium beams and 3 access lids (see Pict. 3). Ensure that the electrical cord and
plug does not get wet.
WARNING: Do not plug in the LED Strip Light if there is water on parts not intended to be wet.
Pict. 8
10
Switching the LED Strip Light On and Off
Plug in the unit and use the line cord switch to turn the LED lighting on
or off. Use exclusively the LED driver supplied with the LED Strip Light.
In all cases make sure that LED driver specifications conform to LED
driver specs indicated in the Roma, Vicenza and Venezia LED Strip Light
identification codes tables below.
Troubleshooting
If the LED Strip Light does not turn on, please proceed as follows:
PROBLEM
The lighting is
not working
If the problem is not solved after following the above, please contact your Hagen retailer.
AQUARIUM MODEL
LED STRIP LIGHT MODEL
LED STRIP LIGHT TYPE
LED DRIVER SPECS
AQUARIUM MODEL
LED STRIP LIGHT MODEL
LED STRIP LIGHT TYPE
LED DRIVER SPECS
LED STRIP LIGHT AND TANK MAINTENANCE
Cleaning the LED Strip Light
Disconnect the Strip Light from power supply before any maintenance operation.
Never place the LED Strip Light under water jets or submerge in water.
No special maintenance is required for the Fluval LED Strip Light and Canopy, other than periodic cleaning
with a damp cloth (never use harsh chemical products or detergents). To remove calcareous deposits, it is
recommended to use a mild acid such as lemon juice, followed by a thorough wipe down with a damp cloth to
remove any residue.
Saltwater aquariums
It is commonly known that salt water is far more corrosive, conductive (of electricity) and generally degrades
both plastic and metal parts at an accelerated rate versus fresh water. To minimize salt accumulations on the
Fluval Canopy and on the LED Strip Light, it is recommended to take note of the following helpful tips:
1. Make sure filter outputs do not spray above the water surface, position them below the water surface with a
slight downward angle, but still allow for surface movement (contributes to oxygenation).
2. If an air pump must be used, frequent removal of salt deposits will be necessary.
3. Keep the water level as constant as possible (regular top-ups due to evaporation). This is beneficial in
providing stable salinity and will help protect the canopy.
4. It is recommended to regularly clean all LED Strip Light components and the Canopies that come into
contact with salt water at least every 15 days. The cleaning should be carried out with a wet cloth (never use
harsh chemical products or detergents). Simple lemon juice may be used to take away salt accumulation.
Pict. 9
Afterwards rinse carefully to eliminate every residue of acid.
CAUSE
Missing connection of the LED Driver to the power outlet Connect the LED Driver to the power outlet
Missing connection of the lighting unit to the LED Driver
ROMA LED STRIP LIGHT IDENTIFICATION CODES
ROMA 90 ROMA 125
Roma Led Unit 90 Roma Led Unit 125
T-47090 T-47125
15VDC 1,25A min. 15VDC 1,25A min.
VICENZA and VENEZIA LED STRIP LIGHT IDENTIFICATION CODES
VICENZA 180 VICENZA 260
Vicenza Led Unit 180 Vicenza Led Unit 260
T-45018 T-45026
15VDC 1,25A min. 15VDC 2,5A min.
WARNING: Be sure you unplug the LED driver from the power outlet; just switching off the lights
with the line cord switch is NOT enough.
Pict. 10
SOLUTION
Connect the lighting unit to the LED Driver with its con-
nector
ROMA 200 ROMA 240
Roma Led Unit 200 Roma Led Unit 240
T-47200 T-47240
15VDC 1,25A min. 15VDC 1,25A min.
VENEZIA 190 VENEZIA 350
Venezia Led Unit 190 Venezia Led Unit 350
T-45019 T-45035 and T-45036
15VDC 1,25A min. 15VDC 2,5A min.
11