IFM DV15 Series Operating Instructions Manual
IFM DV15 Series Operating Instructions Manual

IFM DV15 Series Operating Instructions Manual

5-segment signal lamp

Advertisement

Operating instructions
5-segment signal lamp
UK
DV15x0
DV25x0

Advertisement

Table of Contents
loading

Summary of Contents for IFM DV15 Series

  • Page 1 Operating instructions 5-segment signal lamp DV15x0 DV25x0...
  • Page 2: Table Of Contents

    Contents 1 Preliminary note ���������������������������������������������������������������������������������������������������4 1�1 Key to the symbols ����������������������������������������������������������������������������������������4 2 Safety instructions �����������������������������������������������������������������������������������������������5 3 Functions and features ����������������������������������������������������������������������������������������5 3�1 IO-Link �����������������������������������������������������������������������������������������������������������6 3�1�1 General information ������������������������������������������������������������������������������6 3�1�2 Device-specific information �������������������������������������������������������������������6 4 Installation������������������������������������������������������������������������������������������������������������6 5 Electrical connection ��������������������������������������������������������������������������������������������7 5�1 IO-Link connection �����������������������������������������������������������������������������������������7 6 Pin configuration ��������������������������������������������������������������������������������������������������8 6�1 IO-Link device (DV25x0) �������������������������������������������������������������������������������8 6�2 Standard device (DV15x0) ����������������������������������������������������������������������������8...
  • Page 3 11 Technical data ��������������������������������������������������������������������������������������������������21 11�1 IO-Link device ��������������������������������������������������������������������������������������������21 12 Maintenance, repair and disposal ��������������������������������������������������������������������22 12�1 Cleaning the housing surface ��������������������������������������������������������������������22 13 Approvals/standards ����������������������������������������������������������������������������������������22...
  • Page 4: Preliminary Note

    1 Preliminary note Technical data, approvals, accessories and further information at www�ifm�com� 1.1 Key to the symbols ► Instructions > Reaction, result […] Designation of keys, buttons or indications → Cross-reference Important note Non-compliance may result in malfunction or interference�...
  • Page 5: Safety Instructions

    2 Safety instructions • Read this document before setting up the product and keep it during the entire service life� • The product must be suitable for the corresponding applications and environmental conditions without any restrictions� • Only use the product for its intended purpose (→ 3 Functions and features)� •...
  • Page 6: 3�1 Io-Link

    The IODDs necessary for the configuration of the unit, detailed information about process data structure, diagnostic information, parameter addresses and the necessary information about the required IO-Link hardware and software can be found at www�ifm�com� 4 Installation ► Disconnect power before installation�...
  • Page 7: Electrical Connection

    Integrated seals at the bottom of the fixture and in the base as well as O-rings at the fixture and base prevent ingress of moisture� More information about available accessories at www�ifm�com 5 Electrical connection The unit must be connected by a qualified electrician�...
  • Page 8: Pin Configuration

    6 Pin configuration 6.1 IO-Link device (DV25x0) M12 connector IO-Link, 4 poles (4 x 0�34 mm² / AWG 22) 1: UB+ 2: not used 3: UB- 4: IO-Link 6.2 Standard device (DV15x0) M12 connector, 8 poles (8 x 0�25 mm² / AWG 24) 1: LED segment 5 2: buzzer (DV1510 and DV1530) 3: LED segment 3...
  • Page 9: Operating And Display Elements

    7 Operating and display elements 1: Parameter setting button (only DV15x0) 2: LED segment 1 with 4 RGB LEDs 3: LED segment 2 with 4 RGB LEDs 4: LED segment 3 with 4 RGB LEDs 5: LED segment 4 with 4 RGB LEDs 6: LED segment 5 with 4 RGB LEDs 7: Buzzer (only DVx510 and DVx530) 8: Feedback LED (only DV15x0)
  • Page 10: Operation

    8 Operation 8.1 Operation of the IO-Link version 8.1.1 General The unit is connected to an IO-Link master (A port) with a 4-pole connection cable� The controller switches the individual LED segments on and off in the configured colours according to the set parameters� Via the parameter "Operating mode"...
  • Page 11: 8�1�3 Rgb Mode

    8.1.3 RGB mode While in operation the controller switches the 5 LED segments and the buzzer on and off (only with DVx510 and DVx530), defining the respective properties (PDout, cyclical data communication)� In this operating mode, 8 different acoustic signals are available for the buzzer� PDout Segment 1 LED properties Seg�...
  • Page 12: 8�1�4 Analogue Mode

    Frequency permanently on low flash rate slow low flash rate medium low flash rate fast high flash rate slow high flash rate medium high flash rate fast 8.1.4 Analogue mode While in operation the controller transmits an analogue value between 0 and 100 % in byte 0 via PDout %�...
  • Page 13 The signal lamp generates the following visual indications of the analogue value depending on the data in byte 1� Analogue value: 1-10 % 11-20 % 21-30 % 31-40 % 41-50 % 51-60 % 61-70 % 71-80 % 81-90 % 91-99 % 100 % white white...
  • Page 14: 8�2 Operation Of The Standard Version

    The unit is connected to the digital outputs of the controller via an 8-pole cable (see accessories at www�ifm�com)� The 6 HTTL inputs of the signal lamp are triggered with 24 V DC� According to the set parameters, the 5 LED segments are on and the buzzer sounds (only with DVx510 and DVx530)�...
  • Page 15: 9�2 Standard Version

    9.2 Standard version ► Turn the transparent protective cover anticlockwise by approx� 10 ° and remove it� ► Briefly press the parameter setting button at the head of the unit (< 5 s)� > The feedback LED is green on� The unit is in the parameter setting mode�...
  • Page 16: 9�2�1 Parameter Structure

    9.2.1 Parameter structure Parameter Value seg� Colour green orange blue violet turquoise white yellow Frequency low flash low flash low flash high high high rate rate rate fast flash rate flash rate flash rate slow medium slow medium fast Brightness 75 % 50 % 25 %...
  • Page 17: Scale Drawing

    10 Scale drawing Z_e200_0097 Original Scale Draw 10.1 DVx500 Scale: 1:2 M4x1 M12x1 Dimensions [mm] EPS Source Product Scale Draw Frame Size: 80 mm...
  • Page 18: 10�2 Dvx510

    0_0096 Original Scale Drawing (M 10.2 DVx510 Scale: 1:2 M4x1 M12x1 1: Buzzer Dimensions [mm] EPS Source Product Scale Drawing Frame Size: 80 mm x 90...
  • Page 19: 10�3 Dvx520

    10.3 DVx520 Z_e200_0099 Original Scale Draw Scale: 1:2 M4x1 M12x1 Dimensions [mm] EPS Source Product Scale Dra Frame Size: 80 mm M4x1...
  • Page 20: 10�4 Dvx530

    10.4 DVx530 M4x1 M12x1 1: Buzzer Dimensions [mm] EPS Source Product Scale Drawing Frame Size: 80 mm x 72...
  • Page 21 11 Technical data Operating voltage DC 18���30 Nominal voltage DC Current consumption [mA] ≤ 200 RMS (400 mA for 50 ms) Input current [mA] typ� 6 (24 V DC, high signal) Max� buzzer volume [dB] Degree of soiling Ambient temperature [°C] -25…50 Storage temperature...
  • Page 22 ► Clean the device from dirt using a soft, chemically untreated and dry cloth� ► In case of heavy dirt, use a damp cloth� Micro-fibre cloths without chemical additives are recommended� 13 Approvals/standards EC declarations of conformity, approvals, etc� at www�ifm�com...

Table of Contents