Download  Print this page

Studer SI SERIES User And Installer Instructions

Studer user manual sinewave inverter si series.
Hide thumbs

Advertisement

STUDER INNOTEC
SI
Sinewave inverter
SI SERIES
User's and Installer's Handbook
STUDER INNOTEC
Rue des Casernes 57
CH-1950 Sion
Tel : ++41 (0)27 205 60 80
Fax: ++41 (0)27 205 60 88
info@studer-innotec.com
www.studer-innotec.com
User manual
SI V3.0 E

Advertisement

Table of Contents

   Related Manuals for Studer SI SERIES

   Summary of Contents for Studer SI SERIES

  • Page 1 STUDER INNOTEC Sinewave inverter SI SERIES User's and Installer's Handbook STUDER INNOTEC Rue des Casernes 57 CH-1950 Sion Tel : ++41 (0)27 205 60 80 Fax: ++41 (0)27 205 60 88 info@studer-innotec.com www.studer-innotec.com User manual SI V3.0 E...
  • Page 2: Table Of Contents

    STUDER INNOTEC INTRODUCTION ... 3 NOTE... 3 APPLICATIONS AND PERFORMANCE ... 3 PRODUCT PRESENTATION ... 3 ASSEMBLY ... 4 ... 4 OCATION ... 4 ITTING CONNECTION... 4 USE ... 4 ... 4 EMOTE CONTROL Standby Level (1) ... 5 Adjustment procedure ... 5 CONTROL...
  • Page 3: Introduction

    Due to obvious safety reasons, the inverter is not automatically reactivated after a failure (overload, short circuit,…). Product presentation The inverters of the SI series are presented fully equipped, with battery cables, 230V cable and the user's handbook SI V3.0 E...
  • Page 4: Assembly

    STUDER INNOTEC Assembly Location The place where the inverter is to be mounted should meet the following requirements : Out of reach of non authorised persons. In a dry place with no condensation. No inflammable material in the same room.
  • Page 5: Standby Level (1)

    STUDER INNOTEC Adjustments (Not automatic with Twinpower version) Standby Level (1) The activation of the inverter, when working in automatic mode, is dictated by the detection of a load. With this function, it is possible to adjust the minimum load detected between 0,3 and 20 Watts.
  • Page 6: Options

    We do not accept any responsibility for any violation of patent rights or other third person rights resulting from the use of the inverter. STUDER INNOTEC reserves the right to modify their products without previous notice. CE- declaration of conformity SI V3.0 E...
  • Page 7: Description And Wiring Diagram

    STUDER INNOTEC Description and wiring diagram User manual SI V3.0 E...
  • Page 8: Wiring Diagram For Si 600 - 800 S (solar Charge Regulator)

    STUDER INNOTEC Wiring diagram for SI 600 - 800 S (Solar charge regulator) User manual SI V3.0 E...
  • Page 9 STUDER INNOTEC Option SI performance 3-phased Three SI inverters can be connected together to build a 3-phased grid. They have to be equipped with the PE option. Working Two ways of working are possible with the SI performance : 1) Working alone One SI inverter can be used alone.
  • Page 10: Technical Data

    STUDER INNOTEC Technical data Model SI Input voltage (Unom) [V] Nominal power [W] « Standby » current [mA] Power « ON » no load [W] Power « ON » no load [W] TWINPOWER system Maximum efficiency [%] Length L x 124 (H) x 215 (W) [mm]...

Comments to this Manuals

Symbols: 0
Latest comments:
  • AYMEN-HP May 04, 2013 07:52:
    informatio​n sur J T8 commande a distance