Important Charging Notes - Black & Decker 90516580 Instruction Manual

Cordless compact drills
Hide thumbs

Advertisement

Table of Contents
90516580 CDC9600 CDC1200 etc
CHARGING THE BATTERY PACK (CDC1800) FIGURE B
THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE
ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE
SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger (7) into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not
charge by means of an engine generator or DC power source. Use only 120V
AC
2. Slide the charger onto the battery pack (5) as shown in figure B and let the battery
pack charge initially for 9 hours. After the initial charge, under normal usage, your
battery pack should be fully charged in 3 to 9 hours.
3. Unplug charger, and remove the battery pack. Place the battery pack in the tool
and be certain that it is inserted fully into the tool cavity until it "clicks" into
place.
NOTE: To remove the battery pack from the drill, press down on the release button
(10) on the back of the battery pack (figure D) and slide out.
CHARGING THE BATTERY PACK (CDC9600, CDC1200, CDC1440) FIGURE C
THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE
ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE
SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power.
1. Make sure the battery pack is fitted properly into the drill. Insert the charger plug (8)
into the connector (9) as shown in figure C.
2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet and let the battery
pack charge initially for 9 hours. After the initial charge, under normal usage, your
battery pack should be fully charged in 3 to 9 hours. NOTE: Do not charge by
means of an engine generator or DC power source. Use only 120V AC
3. Disconnect the charger from the outlet, then disconnect the charger from the tool.
NOTE: When installing battery pack, be certain that it is inserted fully into the tool
cavity until it "clicks" into place.
NOTE: Do not use the tool while it is connected to the charger.
NOTE: To remove the battery pack from the drill, press down on the release button
(10) on the back of the battery pack (figure D) and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your battery pack should be fully charged in 3 to 9 hours. If the
battery pack is run-down completely, it may take up to 9 hours to become fully
charged. Your battery pack was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above
105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack.
Longest life and best performance can be obtained if battery pack is charged when
air temperature is about 75°F.(24°C).
3. While charging, the charger may hum and become warm to touch. This is a normal
condition and does not indicate a problem.
4. If the battery pack does not charge properly—(1) Check current at receptacle by
plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to
a light switch which turns power off when you turn out the lights. (3) Move charger
and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C)
(4) If the receptacle and temperature are OK, and you do not get proper charging,
take or send the battery pack and charger to your local Black & Decker service
center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE using product with its
battery pack in a depleted condition.
6. To prolong battery life, avoid leaving the battery pack on charge for extended periods of
time (over 30 days without use). Although overcharging is not a safety concern, it can
significantly reduce overall battery life.
7. The battery pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before
recharging. Normal usage is the best method of discharging and recharging the
batteries.
4/19/07
9:43 AM
Page 7
7

Hide quick links:

Advertisement

Table of Contents
loading

  Related Manuals for Black & Decker 90516580

This manual is also suitable for:

Cdc1200Cdc1440Cdc1800Cdc9600