Table of Contents
Advertisement
Quick Links
Maestro Tilt Hinged Feet Installation
Guide Installation Guide
April 18, 2016
The following guide will provide the necessary step-by-step procedure for installing the constant torque
Tilt Hinged Feet on a Maestro Control Console for the FLEX-6000 Signature Series SDR.
Table of Contents
........................................................................................................................................... 2
Packaging and Tilt Hinged Feet Contents ............................................................................................... 2
Required Tools ........................................................................................................................................ 3
Using the Top Foam Packing Material as an Work Surface Offset ......................................................... 3
Place the Maestro on the Work Surface Offset ...................................................................................... 4
Locating the Tilt Hinged Feet Mounting Screw Holes ............................................................................. 4
Orientating the Tilt Hinged Feet Components ........................................................................................ 5
Install Plugs in Feet ................................................................................................................................. 5
Verify the Correct Orientation of the Feet .............................................................................................. 6
Verify the Correct Orientation of the Hinges .......................................................................................... 7
Attach Hinges to Feet ............................................................................................................................. 7
Prepare Hinge-Foot Assembly for Attachment to Maestro .................................................................... 8
Attach Hinge-Foot Assembly to Maestro ................................................................................................ 8
Page 1
............................................................................................................... 2
............................................................................................................... 3
...................................................................................................... 4
..................................................................................................................... 9
............................................................................ 3
© 2016 FlexRadio Systems, v1.0.1
Advertisement
Table of Contents
Related Manuals for FlexRadio Systems Maestro
Summary of Contents for FlexRadio Systems Maestro
-
Page 1: Table Of Contents
Guide Installation Guide April 18, 2016 The following guide will provide the necessary step-by-step procedure for installing the constant torque Tilt Hinged Feet on a Maestro Control Console for the FLEX-6000 Signature Series SDR. Table of Contents ....................... 2 BTAINING... -
Page 2: Obtaining Technical Support
Getting Started Packaging and Tilt Hinged Feet Contents Remove the Maestro Tilt Hinged Feet kit contents from the packaging and verify that the following items are included before proceeding. Refer to the image below. ... -
Page 3: Required Tools
Using the Top Foam Packing Material as an Work S urface Offset The knobs on the front of the Maestro does not allow for the unit to lie flat on its front to facilitate easy installation of the Tilt Hinged Feet. Therefore the part of the Maestro packing material will be used as an offset to create a flat work surface for installing the Tilt Hinged Feet. -
Page 4: Place The Maestro On The Work Surface Offset
Place the Maestro on the Work Surface Offset As shown in the picture below, place the Maestro touch screen display face down on the top of the foam packing material allow the knobs to rest on the covered work surface. This will allow of the Maestro to lie flat for the installation of the Tilt Hinged Feet. -
Page 5: Orientating The Tilt Hinged Feet Components
SA-11A-140SA-50 on right side. Each hinge is also marked on bottom with “A” and “B” for easy identification. Install Plugs in Feet Insert two each of the plastic plugs into each foot as shown below. Page 5 © 2016 FlexRadio Systems, v1.0.1... -
Page 6: Verify The Correct Orientation Of The Feet
The two (2) mounting holes on the feet are not centered; they are closer to one end of the foot than the other. Before installing the hinges, verify the orientation of each foot so that the mounting holes are farther away from you, towards the Maestro. Page 6... -
Page 7: Verify The Correct Orientation Of The Hinges
Flip the left or “B” hinge over and attach it to the foot with two (2) M4 attachment screws using a #2 screwdriver. Tighten snugly, but do not overtighten. Repeat the procedure for the right or “A” hinge as shown below. Page 7 © 2016 FlexRadio Systems, v1.0.1... -
Page 8: Prepare Hinge-Foot Assembly For Attachment To Maestro
Maestro. Attach Hinge-Foot Assembly to Maestro Position the right hinge-foot assembly “A” on the right side back of Maestro as shown below. Using a #2 screwdriver, attach with two M4 screws. Tighten snugly, but do not overtighten. Repeat the procedure for attaching the left hinge-foot assembly “B”... -
Page 9: Adjusting The Tilt Hinged Feet
Below shows an image of the completed installation of both hinge-foot assemblies. Adjusting the Tilt Hinged Feet The Tilt Hinged Feet are adjusted with the Tilt Hinged Feet on a table and the Maestro in an upright position. Lift Maestro off foam work surface offset and place feet on a flat surface. Grasp the Maestro with two hands as shown below and tilt to the desired operating angle.