Related Manuals for REMKO RR 22.0
Summary of Contents for REMKO RR 22.0
- Page 1 REMKO RR 22.0 Room temperature controller KWK 130 to 870, KWK 130 to 870 ZW, KWD 25 to 100 EC, WLT 25 to 85 S, DKT 21-4 to 71-4 Operation · Technology Edition GB - N01...
-
Page 3: Table Of Contents
Contents Safety notes Intended use Environmental protection and recycling Guarantee Description Operation Installation Instructions for qualified personnel Installation 8 - 9 Adjustable systems and functions Electrical wiring Electrical drawings Commissioning Technical data 12 - 19 Electrical wiring diagram, two-wire system Electrical wiring diagram, four-wire system 20 - 21 Carefully read this operating manual prior to commissioning/using the units! -
Page 4: Safety Notes
Modification of the units and ■ components supplied by REMKO is not permitted and can cause malfunctions. Units and components may not be ■ Intended use operated in areas where there is an increased risk of damage. -
Page 5: Environmental Protection And Recycling
Environmental protection and This accessory is an electronic wall- recycling mounted individual room controller for temperature regulation of indoor units Disposal of packaging for cooling and heating. It automatically All products are packed for transport controls the three fan stages and the in environmentally friendly materials. -
Page 6: Operation
REMKO RR Operation Fan selector switch The remote control is operated using the relevant switches and temperature The fan level can be changed by actuating the selector switch. There controllers. If necessary, also use the are 3 fixed settings ("I" = low,"II" = operating instructions of the unit being medium and "III"... -
Page 7: Installation Instructions For Qualified Personnel
Installation instructions Installation for qualified personnel 1. Disconnect the power supply. 2. Open the controller cover by lifting off Check the contents of the packaging ■ the rotary knob carefully and pressing for completeness and check the in the lock cautiously. unit for visible transport damage. -
Page 8: Adjustable Systems And Functions
REMKO RR Adjustable systems and functions A heating valve connected to terminal 7-8 and a cooling valve connected to Two-wire system with one valve for terminal 8-9 regulate the medium-side cooling or heating (J1=B): flow rate into the heat exchanger of the The controller can be used to control indoor unit in both operating modes. - Page 9 Inlet temperature sensor SM, alternative Valve types bimetallic thermostat BC (terminal 11-12) The controller is only designed to control NC ON/OFF valves: The controller is equipped for use with an SM inlet temperature sensor - an NC valve releases the medium flow (available as an accessory) or a BC rate into the heat exchanger when bimetallic thermostat.
-
Page 10: Electrical Wiring
REMKO RR Electrical wiring Configuring jumper General notes The controller is suitable for controlling three-stage fan convectors. The fan stages are controlled by three potential-free relay outputs at terminals 3 to 5. The controller is designed for controlling ON/OFF valves or an electric heating element. -
Page 11: Electrical Drawings
Commissioning Electrical drawings 1. Switch the unit on using the room Room temperature controller RR 22.0 temperature controller. 2. Program the desired functions. 3. Check all functions. 4. Install all removed parts. 5. Familiarise the operator with the functions. NOTE... -
Page 12: Electrical Wiring Diagram, Two-Wire System
REMKO RR Electrical wiring diagram, two-wire system RR 22.0 with KWD... EC, two-wire system (example) RR 22.0 Room Enabling temperature contact probe Valve assembly (accessory) Inlet Bimetallic temperature thermostat probe (alternative) JP4 = B KWD...EC Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible! - Page 13 RR 22.0 and SR 1 with multiple KWD... EC, two-wire system (example) RR 22.0 Room Enabling temperature contact probe Inlet Bimetallic temperature thermostat Valve assemblies (accessories) probe (alternative) JP4 = B SR 1 (Accessory) Further units KWD...EC KWD...EC Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible!
- Page 14 REMKO RR RR 22.0 with WLT... S, two-wire system (example) RR 22.0 Enabling Room contact temperature probe Bimetallic Inlet temperature thermostat probe (alternative) JP4 = B Valve assembly (Series) WLT...S Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible!
- Page 15 RR 22.0 and SR 1 with multiple WLT... S, two-wire system (example) RR 22.0 Room Enabling temperature contact probe Bimetallic Inlet thermostat temperature (alternative) probe JP4 = B SR 1 Further units WLT...S WLT...S Valve Valve assembly assembly (Series) (Series)
- Page 16 REMKO RR RR 22.0 with CHP, two-wire system (example) RR 22.0 Room Enabling temperature contact probe Bimetallic Inlet thermostat temperature (alternative) probe JP4 = B Valve assembly (accessory) Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible!
- Page 17 RR 22.0 and SR 1 with multiple CHP, two-wire system (example) RR 22.0 Room temperature Enabling probe contact Bimetallic Inlet thermostat temperature (alternative) probe JP4 = B SR 1 Further units Valve assembly Valve assembly (accessory) (accessory) Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible!
-
Page 18: Electrical Wiring Diagram, Four-Wire System
REMKO RR Electrical wiring diagram, four-wire system RR 22.0 with DKT... -4, four-wire system (example) RR 22.0 Enabling Room temperature contact probe Bimetallic Inlet thermostat temperature (alternative) probe JP4 = B Heating valve assembly (provided by the customer) Cooling (Series) DKT...-4... - Page 19 RR 22.0 with CHP, four-wire system (example) RR 22.0 Room temperature Enabling probe contact Bimetallic Inlet thermostat temperature (alternative) probe JP4 = B KWK with HR 6 Four-wire valve assembly (accessory) Technical modifications reserved. Information provided without guarantee. Customer-specific modification possible!
- Page 20 REMKO INTERNATIONAL ... and also right in your neighbourhood! Take advantage of our experience and advice REMKO GmbH & Co. KG Air conditioning and heating technology Im Seelenkamp 12 D-32791 Lage Postfach 1827 D-32777 Lage Telephone +49 5232 606-0 +49 5232 606-260 E-mail info@remko.de...
Need help?
Do you have a question about the RR 22.0 and is the answer not in the manual?
Questions and answers