Page 1
BRUKSANVISNING SV ... 8 KÄYTTÖOHJEET FI ... 19 BRUGSANVISNING DA ..30 BRUKSANVISNING NO .41 GEBRAUCHSANWEISUNG DE...52 INSTRUCTIONS FOR USE EN...64 MODE D’EMPLOI FR...75 GEBRUIKSAANWIJZING NL...87 8211-0005-70 S T I G A P A R K P R O 2 5 P R O 2 0 P R O 1 6 P R O S v a n...
1 GENERAL This symbol indicates WARNING. Seri- ous personal injury and/or damage to property may result if the instructions are not followed carefully. You must read these instructions for use and the accompanying pamphlet “SAFETY INSTRUCTIONS” careful- ly, before starting up the machine. 1.1 SYMBOLS The following symbols appear on the machine.
Page 9
same pressure and can follow the contours of the ground. Use the floating position when carrying out work. Lowering. The implement lowers re- gardless of its weight. Locking in the transport position. The lever has returned to the neutral position after raising and lowering.
Page 10
2.4.9 Ignition lock/headlight (4,5:I) The ignition lock is used for starting and stopping the engine. The ignition lock is also the switch for the headlight. Do not leave the machine with the key in position 2 or 3. There is a fire risk, fuel can run into the engine through the carburettor, and there is a risk of the battery being discharged and damaged.
2. Install the locking pin (34:G). 3. Carry out the above on the other side. ENGLISH 3 AREAS OF USE The machine may only be used for the following tasks using the genuine STIGA accessories stated. Work Accessories, STIGA genuine Mowing Using mowing decks:...
Environmental petrol can be used, i.e. alkylate petrol. This type of petrol has a composition that is less harmful for people and nature. Petrol is highly inflammable. Always store fuel in containers that are made especially for this purpose. Only fill or top up with petrol outdoors, and never smoke when filling or top- ping up.
4.4 Start 1. Open the fuel cock. See 14. 2. Check that the spark plug cable(s) is/are in- stalled on the spark plug(s). 3. Check to make sure that the power take-off is disengaged. 4. Do not keep your foot on the drive pedal (3:F). 5.
Front: 0.6 bar (9 psi). Rear: 0.4 bar (6 psi). 5.4 Changing engine oil, filter This section contains tables covering the different engines that are included in STIGA’s Pro range. To facilitate reading, mark the data that applies to the relevant machine/engine. ENGLISH 5.4.1 Change intervals...
1. Attach the clamp on the oil drainage hose. Use a polygrip or similar. See fig. 15-17:Y. 2. Move the clamp up 3-4 cm on the oil drainage hose and pull out the plug. 3. Collect the oil in a collection vessel. NOTE! Do not spill any oil on the drive belts.
4. Check that the rubber gasket (21:H) at the bot- tom of the filter is intact. 5. Install the new filter and the spring in the sleeve. Insert the filter until it snaps into place in the sleeve. 6. Reinstall the unit in the tank. The upper section of the filter must click securely into the recess in the upper section of the tank.
5.9.3 Removal/Installation The battery is placed under the tank. To access the battery, first dismantle the fuel tank as follows: 1. Open the engine casing. 2. Close the fuel cock, see 14. 3. Unscrew the two wing nuts (16:B) and remove the clamps.
5.10.3Air filter (Pro Svan) Clean the air filter every 3 months or after every 50 hours of operation, whichever comes first. Clean the paper filter insert once a year or after every 200 hours of operation, whichever comes first. Note! Both filters should be cleaned more often if the machine operates on dusty ground.
Page 19
w w w. s t i g a . c o m GGP Sweden AB · Box 1006 · SE-573 28 T RANÅ S...
Need help?
Do you have a question about the PARK PRO 25 and is the answer not in the manual?
Questions and answers