External dust and chip extraction Inserting/changing the batteries Setting up Adjusting the parallel guide stop Adjusting the bevel angle Adjusting the cutting depth Laser guidance On/o switch Sawing Recommendations for use 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Page 8
Maintenance and cleaning Inspecting the device Disposal Service/customer support EU declaration of conformity Exploded drawing Spare parts list Warranty card 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Batteries containing a toxic material are additionally marked with the chemical symbol for the toxic material (Hg - mercury, Cd - cadmium, Pb - lead). 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Only use extension leads approved for use outdoors when using an electric power tool in the open. The use of an extension cable suitable for outdoor use reduces the risk of an electric shock. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Pull the plug from the socket and/or remove the battery before you make any adjustments to the tool, change accessories or put the tool away. This precautionary measure prevents the electric power tool starting unintentionally. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Contact with a live wire will make the metal parts of the power tool live too and cause an electric shock. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Page 13
Support large panels to avoid the risk of kickback as a result of a binding saw blade. Large panels can sag under their own weight. The panels must be supported on both sides, both close to the kerf and at their edges. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
The vibration emission value stated can also be used for a preliminary assessment of exposure. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Page 15
You can reduce the adverse e ect from these chemicals by working in a well ventilated area and with approved protective equipment, such as dust masks. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
· Remove batteries from the device if it is not to be used for some time. Function description Read all safety notes and instructions. Failure to observe the instructions set out below can lead to an electric shock, re and/or serious injuries. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Undo the wing nut (7) and remove the parallel guide stop (8). • Loosen the depth adjustment locking lever (27) and set the cutting depth to the minimum position “0 mm”. Tighten the depth adjustment locking lever (27) again. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Page 19
Observe the regulations for the materials to be worked valid in your country. Note: Always use the elbow connector for the external dust extraction (21) when sawing to avoid being injured by ejected chippings. 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Slacken the wing nut for the parallel guide stop (7) on the soleplate (10) and push the parallel guide stop (8) into the groove provided. • Set the parallel guide stop to the desired distance and retighten the wing nut (7). 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Press the lock-o button (25) and then the mains switch (1), press and hold the mains switch (1). The hand-held circular saw is equipped with electronic soft starting. The motor starts after a brief delay. Switch o : Release the mains switch (1). 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Always hold the circular saw with both hands and push the saw through the material with appropriate forward pressure. The M1Y-DU10-190 hand-held circular saw has Intelligent Power Control, a smart constant electronics system. The constant electronics system ensures a constant speed of rotation whatever the loading on the motor as a result of the hardness of the material or the advance pressure.
Please contact our service partner if you have any queries or wish to order parts: Sertronics GmbH MEROTEC Service Center Ostring 60 66740 Saarlouis, Germany Fax: +49 6831 4880 820 Email:merotec@sertronics.de 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
MEROTEC GmbH Graf-Recke-Strasse 82, 40239 Düsseldorf, Germany Hereby declare that our product: 1500W CIRCULAR SAW WITH LASER Model number: M1Y-DU10-190 complies with the essential industrial health and safety requirements in accordance with the following directives: EMC Directive: 2004/108/EC Machinery Directive: 2006/42/EC...
Parallel guide stop Coil winding Wrench Self-tapping screw Soleplate Ball bearings (6000) Armature Washer Ball bearings (608) Bevel angle adjustment wing nut Motor casin Parallel guide stop wing nut 0845 872 2740 019022605 After Sale support M1Y-DU10-190 / 90704 www.sumecservicecentre.co.uk...
Page 27
* We recommend that you keep the receipt with this warranty card. Place of purchase Description of fault: CUSTOMER SUPPORT Send the completed warranty card to: Units A,B 0845 872 2740 Escrick Business Park 019022605 Escrick York Model: M1Y-DU10-190 , 08 / 2013, 90704 YO19 6FD E-mail: support@coreservice.co.uk YEARS WARRANTY...
Need help?
Do you have a question about the M1Y-DU10-190 and is the answer not in the manual?
Questions and answers