Page 9
SD1600V Explanation symbols Explanation symbols symbols in this intended draw manual attention risks. possible your safety symbols that explanations them be understood must accompany before using scroll in themselves saw. warnings risks remove cannot replace correct actions preventing accidents. “CAUTION...
Page 10
Introduction SD1600V 1. Introduction WORKZONE® Congratulations choosing product. WORKZONE® products brought manufactured highest standards performance safety, part philosophy customer service satisfaction, backed comprehensive 3 Year Warranty. will hope enjoy using purchase your many years come. Note: According law the manufacturer...
Page 12
SD1600V Scope delivery/Intended Scope delivery generator carefully. Open packaging remove material well transport bracing packaging Remove packaging (if available). Check that delivery complete. damage. Check parts transport generator accessory until period expired. warranty possible, store packaging (1x) Scroll Blow-off device...
Page 13
Intended information SD1600V use/Safety have with these service equipment acquainted persons equipment’s potential informed about instructions operating must hazards. accident in force in your It is also imperative observe prevention regulations area. rules health work. general safety applies same liable...
Page 14
SD1600V information Safety shoes Rubber gloves non-slip get caught moving parts. They hair. outdoors. Wear hair have long recommended when working mask when Wear dust safety goggles. personal safety equipment. working dusty jobs. other than that which it cable designed.
Page 15
SD1600V Safety information customer service Never electric workshop. tool with switch that power turned off. cannot Important. safety your must only accessories addi- tional units listed operating instructions recommended specified manufacturer. mounted tools accessories other than those recommended operating instructions...
Page 16
Safety information SD1600V Never loose remove splinters, chips jammed pieces wood when blade running. Switch machine faults rectify blocked tool. Disconnect plug-in Remove plug- blockage. Important! Risk from blade! Wear power injury gloves. Carry trial without Ensure that unusual noise workpiece.
Page 17
SD1600V information Safety position, join, construct parts table while work running. Only switch after have removed remaining material tools from work table. Leave only workpiece machined aids (e.g. table. wedges) on work Always safety wear goggles! Keep your fingers safe...
Page 18
Technical data SD1600V 6. Technical data Mains voltage 220-240 V~ / 50 Hz Watt (S1) Power input 120 Watt (S6 30%) min” Stroke 1700 rate IP20 Protection type 21mm Stroke Base area 0° 45° to theleft of table Tilting range...
Page 19
SD1600V Technical data Noise emission values Sound Sound values measured in accordance were with EN 61029. Wear ear-muffs. impact noise cause damage hearing. Sound pressure level 66.9 L,,: dB(A) Uncertainty K,,,: dB(A) Sound power level 79.9 dB(A) L,,: Uncertainty K,,,:...
Page 20
SD1600V Before machine starting machine 7. Before starting before making adjustments Important! Always pull plug power equipment. information General before equipment devices have properly fitted safety covers switched for the blade It must possible freely. watch out with that been...
Page 21
SD1600V Before starting machine Tighten with secure second (G). Assembly Important! Always pull plug before carrying power maintenance conversion on the scroll work saw. Mounting blade guard blow-off device (Fig. 6/7/8) Remove the bracket (22) from device retaining (21) with...
Page 22
SD1600V machine starting Before 4/91/10/11/ pin (Fig. with blades Removing fur- required, (11) upwards. lever tightening lifting tension Release anti-clockwise. turning tension reduce ther insert (7). table Remove holder (I). blade down the upper Slightly press blade holders (I). from...
Page 23
SD1600V Before starting machine/Operation Carry test precise Test machining: angle by making sample checking respective number degrees workpiece using angle Readjust gauge. pointer (L) necessary. Operation Note: does wood automatically. Rather, operator must push guide wood toward moving blade. teeth...
Page 24
SD1600V connection Operation/Electrical (Fig. 19) cutting Miter guard (5) blade distance adjust miter cuts To carry lever (14) locking (6) by loosening table Swivel (6) accordingly. table lever (14). locking Tighten desired position. to the table tilting angle cuts. miter...
Page 25
SD1600V Electrical connection/Cleaning, maintenance storage Please provide information following event enquiries: Type current motor Machine data type plate Cleaning, maintenance storage Important! Always p ull plug before power starting cleaning work. Cleaning Keep safety devices, vents motor housing free dirt and dust possible.
sscheppach Fabrikation Holzbearbeitungsmaschinen GmbH Ginzburger Str. » D-89335 Ichenhausen C€ Declaration Conformity inde Konformitat gemas prehlasuje nasledujticu zhodu podla smernice Normen fiir den Artikel noriem vyrobok hereby declares following conformity under kinnitab jargmist vastavus vastavalt ELi direktiivi Directive standards following article standardite artiklinumbrit...
Page 30
SD1600V SUPPORT AFTER SALES 4003 4003 00800 & service.uk@scheppach.com CODE: 85590 10/2018 PRODUCT MODEL: SD1600V...
Page 31
SD1600V AFTER SALES SUPPORT & service.uk@scheppach.com 00800 4003 4003 MODEL: SD1600V PRODUCT CODE: 85590 10/2018...
Page 32
PRODUCED CHINA FOR: ALDI STORES LTD., PO BOX 26, ATHERSTONE, WARWICKSHIRE, 2SH. ALDI STORES LTD. (IRELAND) PO BOX NAAS, 726, KILDARE. Visit at www.aldi.com AFTER SALES SUPPORT 00800 4003 4003 & service.uk@scheppach.com MODEL: SD1600V PRODUCT CODE: 85590 10/2018 YEAR WARRANTY...
Page 33
00800 4003 4003 return product please completed ‘service.uk@scheppach.com card with it. & warranty together GreatStar Europe MODEL: SD1600V PRODUCT CODE:85590 10/2018 Unit 55 Romsey Industrial Estate, Romsey, Hampshire Phone lines available $051 Monday Friday, United Kingdom 6pm. Email: service.uk@scheppach.com...
Page 34
conditions Warranty Dear Customer; ALDI Warranty offers you extensive benefits in addition to your statutory rights: Warranty 3 years from date purchase. period: Costs: Free repair/exchange. cosis. transport Hotline Free hotline ADVICE: Please service hotline e-mail contact our by phone, before sending the device.
Need help?
Do you have a question about the SD1600V and is the answer not in the manual?
Questions and answers