Subscribe to Our Youtube Channel
Related Manuals for MONARCH INSTRUMENT SLS-115
Summary of Contents for MONARCH INSTRUMENT SLS-115
- Page 1 SLS-115/230 Smart Laser Sensor 15 Columbia Drive Amherst, NH 03031 USA Phone: (603) 883-3390 Fax: (603) 886-3300 E-mail: support@monarchinstrument.com Website: www.monarchinstrument.com...
- Page 2 (730 m) away. Can be a distraction up to 4.5 miles (7.3 km) away. NEVER point any laser towards aircraft or vehicles; it is unsafe and illegal. Manufacturer: Safe use guidance Monarch Instrument Class 3R lasers are safe when handled 15 Columbia Drive carefully.
-
Page 3: Table Of Contents
11.0 OPTIONS AND ACCESSORIES ......... BACK Symbols on the unit and in this manual: Direct current Warning Laser Beam Alternating current Caution Read Manual Monarch Instrument’s Limited Warranty applies. See www.monarchinstrument.com for details. Warranty Registration and Extended Warranty coverage available online at www.monarchinstrument.com. -
Page 4: Overview
OVERVIEW The Smart Laser Sensor (SLS) is a self-contained unit intended to be used to make non-contact speed measurements from rotating targets at distances up to 65 feet (19.8 m) or to provide non-contact reference points to balancing equipment. Refer to Section 6.0 for an overview of operation. The unit will output one (TTL Compatible) pulse per revolution and has the ability to compute the RPM internally and output the ASCII values to any equipment capable of receiving an RS232 input. - Page 5 Laser On LED Blinks when unit is first turned on. Remains lit when the laser beam is on. Auto/Gain LED On solid whenever the unit is in the Auto mode. It also blinks from 1 to 8 times to indicate the current gain whenever the gain is changed.
-
Page 6: Quick Start Guide
QUICK START GUIDE Note: Refer to Figure 1 for switch and button locations. Slide Power switch (8) to “On”. Rotate Sensitivity Adjust knob (7) fully counterclockwise to the “Auto” position. Aim the laser dot perpendicular to the target - reflective tape, contrasting color or keyway. -
Page 7: Connection Detail
CONNECTION DETAIL Pulse/ The unit has an input power jack for RS232 power recharging Output batteries. Use only the PR Universal charger supplied. The unit also has a five-pin DIN output socket for Pulse outputs and RS232. An 8-foot [2.5 m] cable with a DIN plug and BNC connector is supplied. -
Page 8: Operation
Figure 3 Pin Connections OPERATION Note: Refer to Figure 1 for switch and button locations. Turn the unit on by moving the Power switch (8) to the On position. The unit may be operated from the internal batteries and/or the charger/power supply. -
Page 9: Auto Mode
pulse) or low (negative pulse). The user can select either a positive or a negative output pulse using the Polarity switch (5). The gain of the input amplifier and the sensitivity can be adjusted manually or automatically. This allows the unit to be used with many types of targets at various distances and contrasting color conditions. -
Page 10: Advanced Feature (Target Polarity)
Press and release the Learn/Gain button (6) to change the gain of the input amplifier. Each time the button is pressed, the gain is changed. The Auto/Gain LED (3) will blink to show what gain has been selected. If the button is held down, the gain will increase automatically after each LED „blink‟... -
Page 11: Rs232
Do not stare directly into the laser beam or the reflected light. For targets greater than 5 feet and up to 65 feet from the sensor, mount the laser on a tripod using the ¼ - 20 bushing on the bottom of the unit and attach T-5 reflective tape to the target. -
Page 12: Charging
CHARGING Slide the Power switch (8) to the Off/Charge position and plug in the charger. The Power LED (4) will blink red while the unit is fast charging. The Power LED will blink amber when slow (trickle) charging. It will be solid amber when the batteries are fully charged. -
Page 13: General
10.2 General Operating Range: Up to 65 feet depending on target reflectivity: 1/2” reflective tape (T-5) @3600 RPM: up to 65 ft. (19.8 m) or up to 75° from target White/Black contrast @3600 RPM: up to 3 ft. (91 cm) or up to 45°... - Page 14 PR Universal Charger: Input: 100-240 V , 50-60 Hz Output: , Dry location use only Check charger label for power information. Pulse Output: Source Output - Square Wave 0 to 3.9V typical @ 15mA (PNP to 4.2V, 4.7K ohms to common) (TTL Compatible) Open Collector - Switches to common, External pull up resistor to user supplied power (max 24 V...
-
Page 15: Installation Environment
10.3 Installation Environment Installation Category II per IEC 664 Pollution Degree Level II per IEC 61010-1 Temperature: 32 to 104 F (0 to +40 C) operating 14 to 158 F (-10 to +70 C) storage Humidity: Maximum relative humidity temperatures up to 88 °F (31 °C) decreasing linearly to 50% relative humidity at 104 °F (40 °C) 10.4 Compliance Please visit our website www.monarchinstrument.com to download... -
Page 16: Options And Accessories
SLS Battery Pack Replacement rechargeable Ni-Cd batteries PR Universal Recharger/Power Supply with assorted adapter plugs Check out some of our other product lines… Tachometers Track-It™ Data Loggers Stroboscopes Printed in the U.S.A. Copyright 2016 Monarch Instrument, all rights reserved 1071-4859-114 -0916...
Need help?
Do you have a question about the SLS-115 and is the answer not in the manual?
Questions and answers