Advertisement
Quick Links
Advertisement
Related Manuals for LEGRAND HKRL20
Summary of Contents for LEGRAND HKRL20
- Page 1 Smart Remote Switch Room HKRL20...
-
Page 2: Table Of Contents
table of contents before you start ........3 faqs ..........23 what you need ........4 regulatory information ..24–27 getting to know your remote switch warranty ........28 ............6-7 support ........29 installation and setup ....8–22... -
Page 3: Before You Start
• The remote switch pairs ONLY with codes the smart switch (HKRL10) for multi- • Install in a non-metallic electrical box location control to protect wireless signal strength Visit the Legrand website at www legrand us/radiant/homekit aspx to learn more about your smart device... -
Page 4: What You Need
what you need REQUIRED: Phillips-head screwdriver Flat blade screwdriver YOU MAY ALSO NEED: Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, radiant screwless wallplate (included), wiring leads (included), and ® wire nuts (included) NOTE: Exercise caution when using power tools. Overtightening the screws can damage the device. -
Page 6: Getting To Know Your Remote Switch
• To return the switch to factory default, press and Paddle Switch hold the top of the paddle for 15 seconds Then, remove the device from the Legrand Home app (or Apple Home app) Indicates the current state of the device Refer to LED Locator Light “LED Locator Light Explanations”... - Page 7 LED LOCATOR LIGHT EXPLANATIONS State of Light Explanation Color Slowly Flashing Device is attempting to connect to Amber the network Solid White Connected to Wi-Fi and turned off No Light Device is on Rapidly Flashing N-Way Pairing mode: device is Green attempting to pair with the master Rapidly Flashing...
-
Page 8: Installation And Setup
• If you are installing your master device at the same time as the remote device, make sure power is off to both devices. • For detailed instructions on how to install your three-way remote product, please visit legrand.us/3wayinstallationinstructions. - Page 10 installation & setup step two remove the existing device Check for the following wires: HOT or LINE: Receives power from the circuit box Referred to as “hot” for the purposes of this guide Do not touch or let “hot” wires contact other wires LOAD: Directs power to your light(s) NEUTRAL: Creates a path to return current to the power source, when the device is off Required for your switch installation...
- Page 11 NOTE: Supply “Hot” This illustration depicts the location for the remote product. For detailed instructions on how to install your three- way remote product, please visit: www.legrand.us/ 3wayinstallation Master instructions.aspx. (Smart Switch)
- Page 12 installation & setup step three wire the smart remote switch When connecting each wire, loosen the terminal screw, insert the wire into a terminal slot, and tighten the terminal screw until the wire is secured Master Remote Connect the neutral wires to the Connect the neutral wires to the WHITE terminal slots WHITE terminal slots...
- Page 13 MASTER REMOTE Terminal screw Supply Load “Hot” Terminal slot NOTE: The master device is always on the load side. If you are unsure about your wiring, consult the “faqs” on page 23, technical support, or a licensed electrician.
- Page 14 installation & setup step four secure the smart remote switch Gently fold the wires into the electrical box Be careful not to pinch a wire or loosen any wire nuts Use the device screws to secure the smart remote switch to the electrical box Do not fully tighten the screws...
- Page 16 Be sure the Smart Switch (master device) has been added to the Apple Home and Legrand Home apps Follow the instructions provided with the master product Hold the top of the paddle on the remote device for 15 seconds until the LED indicator...
- Page 18 installation & setup Hold the top of the paddle of the remote device for five seconds The LED indicator on the remote device should begin to rapidly flash green This indicates the remote device is trying to pair with the master product If the pairing is successful, the LED indicator on the remote will rapidly flash amber indicating the master device has been found and then flash solid amber to show successful pairing...
- Page 19 TROUBLESHOOTING TIP: If the device is not powering, reference the “faqs” on page 23 to determine if you have reversed the “hot” and “load” wiring LED LOCATOR LIGHT EXPLANATIONS State of Light Explanation Color Slowly Flashing Amber Device is attempting to connect to the network Solid White Connected to Wi-Fi and turned off No Light...
- Page 20 installation & setup step six attach the screwless wall plate Noting which side faces out, align the sub-plate over the device screws Use the sub-plate screws (provided) to secure the sub-plate to the smart remote switch Tighten the device screws to secure the smart remote switch to the electrical box Angle the end of the screwless wall plate over the top edge of the sub-plate Push the screwless wall plate down and in until it “snaps”...
- Page 22 The use of a HomeKit-enabled accessory requires the following permissions: • Settings> iCloud > iCloud Drive> Turn On • Settings> iCloud > Keychain > Turn On • Settings> Privacy > HomeKit > Legrand Home> Turn On For troubleshooting visit https://www legrand us/support/onq aspx Keep your individual HomeKit Setup Code in a secure area.
-
Page 23: Faqs
faqs Which wire is the “hot” wire versus the “load” wire? To determine this safely, begin by confirming that power is off to the device location at the circuit breaker Cap all of the exposed wires in the electrical box, then turn the power back on to the device location Find your non- contact voltage tester Place your voltage tester next to each of the wires The voltage tester should indicate which of the two wires is receiving power from the circuit box (refer to the voltage tester’s user manual for details on... -
Page 24: Regulatory Information
regulatory information FCC NOTICE This device complies with Part 15 of the FCC Rules and Industry Canada license- exempt RSS standard(s) Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules These limits are designed to... - Page 25 If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •...
- Page 26 regulatory information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 cm between the transmitter’s radiating structure(s) and the body of the user or nearby persons This transmitter must not be co-located or operating in conjunction with any other antennae or transmitter The antennas used for this transmitter must be installed to provide a separation distance of at least 0 5 cm from all persons and must not be co-...
- Page 27 IC NOTICE This device complies with Industry Canada license-exempt RSS standards Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device RF EXPOSURE STATEMENT This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 15 mm to the human body Note: Any changes...
-
Page 28: Getting To Know Your Remote Switch Warranty
warranty This product is warranted under normal use against defects in workmanship and materials for as long as you own it If the product fails due to a manufacturing defect during normal use, return it for a replacement at the store where purchased or contact Technical Support at 1-800-223-4162, option 3 All replacement requests must include a dated sales receipt (legible copies are acceptable) -
Page 29: Support
IF YOU NEED HELP INSTALLING YOUR DEVICE, TALK TO OUR TECHNICAL SUPPORT TEAM: PHONE: 1-800-223-4162, option 3 8:00 a m to 5:00 p m EST (M-F) EMAIL: technical support-hs@legrand us CHAT: https://www legrand us/support/onq aspx (Click on the icon to open a dialogue box) - Page 30 Legrand, North America 301 Fulling Mill Rd, Ste. G Middletown, PA 17057 1-877-833-3303 www.legrand.us ©2019 Legrand All Rights Reserved 1507300 Rev D 02/19...
Need help?
Do you have a question about the HKRL20 and is the answer not in the manual?
Questions and answers