jcb 18z-1 Quick Start Manual
Compact excavators
Hide thumbs
Also See for 18z-1:
- Quick start manual (28 pages) ,
- Service manual (51 pages) ,
- Operator's manual (31 pages)
Advertisement
Advertisement
Table of Contents
Related Manuals for jcb 18z-1
Summary of Contents for jcb 18z-1
- Page 1 Quick Start Guide QUICKSTART.JCB.COM Compact Excavators 18z-1, 19c-1, 19c-1 EP...
-
Page 2: Table Of Contents
Maintenance Position ........................19 > Operation of this machine without periodic maintenance could cause it to malfunction. Service / Maintenance ........................20 For more information please contact your JCB Dealer. Access Covers ..........................21-22 Fluids & Lubricants ..........................23 Machine Attachments ........................24 Troubleshooting / FAQs ......................25-26 Your Notes ............................27... -
Page 3: Intended Use
3860 3862 Track height M Counterweight clearance N Operating mass* 1749 1910** 1943** * Standard machine specification, please see data plate for specific machine weight. * * Cab variant. Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP... - Page 4 REFER TO OPERATORS MANUAL TRANSPORTING MACHINE REFER TO OPERATORS MANUAL TRANSPORTING MACHINE 17. Remove both ramps and attach them in their transport position. 18. Raise any jacks to their transport position. Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP 9831/2900-1...
-
Page 5: Lifting Points
Operation Lifting Points Lifting the Machine Cab & Switch Panel 7. Check that the lifting eye is positioned directly above the machine centre of gravity. Operator Station Layout – 18z-1, 19c-1 Figure 84. Fig 4 Fig 6 A Auxiliary pedal... - Page 6 Worklights on/off switch LED illumination: 1= Front on, 2= Rear on Master warning Service due warning Audible/Visual. If amber light illuminate then contact JCB d Illuminate amber when service is due. high flow) Wiper/washer on Push to change wiper function (Intermittent /on/off). Hold to operate washer.
- Page 7 Audible/Visual. The lamp illuminate red and buzzer will sound, if battery is Auxiliary Circuit Controls Master warning Audible/Visual. If amber light illuminate then contact JCB dealer. If red light ately and contact your JCB Dealer. motive Engineers) ac- High travel speed Illuminate green when high travel speed is selected.
- Page 8 Entering and Leaving the Operator Station Seat Belt General General For: 18Z-1 ..........................Page 36 Joystick & Dozer Lever Start Up Sequence For: 16C-1, 19C-1 ........................Page 38 WARNING Operating the machine without a seat belt can be dangerous. Before starting the engin sure your seat belt is fastened.
- Page 9 Grease the Quickhitch daily. If the Quickhitch is cleaned by high pressure water, always grease it afterwards. Visually inspect the condition of the hydraulic hoses to the Qucikhitch. 9831/2900-1 9831/2900-1 Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP...
-
Page 10: Maintenance Position
B Boom swing/aux changeover b changeover for tilt-rotator flow) *19c-1 EP only please refer to the operators manual for 19c-1 and 18z-1 E Right electro-proportional switch for aux 1 (high ctro-proportional switch for aux 2 (low D Right finger button - hammer... -
Page 11: Service/Maintenance
Check condition and tension of tracks Visual check 9831/2900-1 Check presence of all pivot pin retaining bolts Visual check Grease slew ring bearing Lubricate Grease window and door hinges Lubricate Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP 9831/2900-1... -
Page 12: Fluids & Lubricants
All Other Grease JCB MPL-EP Grease 4003/1501 0.4kg required JCB part numbers are liable to change and may also vary by region. For the latest information, always check with your dealer/distributor. 9831/2900-1 A Radiator cap B Hydraulic tank filler cap... -
Page 13: Machine Attachments
Breaking up tarmac, concrete, rock aux service 1x single acting Breaker –HM100Q Breaking up tarmac, concrete, rock aux service ATTACHMENT WEIGHTS ARE A GUIDE ONLY, ALWAYS CHECK YOUR OWN ATTACHMENTS Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP... -
Page 14: Your Notes
Please refer to page 14 for joystick control layout. Aux Flow L/min Aux Pressure bar (psi) 200 (2898.5) What are the max flows and pressures of the Auxiliary circuits? 200 (2898.5) 200 (2898.5) Please see operator manual for full details. 18z-1, 19c-1, 19c-1 EP... - Page 15 They should not therefore be relied upon in relation to suitability for a particular application. Guidance and advice should always be sought from your JCB Dealer’. JCB reserves the right to change specifications without notice. Illustrations and specifications shown may include optional equipment and accessories.