Programming Remote Controls - Chamberlain T Installation Manual

PROGRAMMING REMOTE CONTROLS

To prevent possible SEVERE INJURY or DEATH:
• Install a LiftMaster Monitored Entrapment Protection (LMEP)
device.
• NEVER permit children to operate or play with door control
push buttons or remote controls.
Built in 3-channel, Security+ 2.0
add up to 90 remote control devices and up to 30 keyless entry
devices.
NOTE: The following programming requires a LiftMaster
Monitored Entrapment Protection (LMEP) device.
STANDARD REMOTE CONTROL
1. To enter programming, press and release the RADIO button on
the logic control board (RADIO LED will light).
2. Press and hold the remote control button until the RADIO LED
flashes rapidly, then release remote control button. The RADIO
LED will then remain on solid. Repeat to add additional remote
control(s).
3. Press and release the RADIO button to complete the
programming. The RADIO programming mode will exit if no
activity is performed within 30 seconds. The MAS and RADIO
LED's will flash briefly to indicate the RADIO has exited the
programming mode for remote controls and keyless entry
devices. The RADIO will remain in program mode for another
®
150 seconds for MyQ
with no activity.
SINGLE BUTTON REMOTE CONTROL PROGRAMMED AS
A SINGLE BUTTON CONTROL (SBC)
This function programs a remote control as a wireless single
button control. This function will work in the following modes:
In B2 mode, operation is OPEN/STOP/CLOSE/REVERSE/STOP.
In T and TS modes, operation is OPEN/STOP/CLOSE/REVERSE/
STOP and Timer-To-Close start/refresh. NOTE: If Car Dealer mode
is enabled, SBC will be open only stopping at the Open Mid-Stop.
In FSTS mode, operation is OPEN with Timer-To-Close
start/refresh only, bypassing a programmed Open Mid Stop.
1. Press and release the RADIO button on the logic control board
(RADIO LED will light).
2. Press and release the SBC externally wired button. The RADIO
LED flashes rapidly and remains on solid. (If an SBC externally
wired button is not present, a jumper wire may be used to
momentarily short SBC and COMMON.)
3. Press and hold the remote control button until the RADIO LED
flashes rapidly. The RADIO LED will then remain on solid after
releasing.
®
radio receiver that allows you to
devices and then will completely exit
• Activate door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER
permit anyone to cross the path of closing door.
4. Press and release the RADIO button on the logic control board
(RADIO LED flashes rapidly and then turns off). The
programming mode is exited if no activity is performed within
30 seconds. The MAS and RADIO LED's will flash briefly to
indicate the RADIO has exited the programming mode for
remote controls and keyless entry devices. The RADIO will
remain in program mode for another 150 seconds for MyQ
devices and then will completely exit with no activity.
NOTE: Single button remote control is not supported with D1 and
E2 wiring modes. C2 mode will only open and stop while opening.
ERASING REMOTE CONTROLS
Press and hold the RADIO button on the logic control board until
the RADIO LED flashes rapidly (approximately 5 seconds).
All remote controls will be erased.
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this
transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modifications not
expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment. This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation. This Class B
digital apparatus complies with Canadian ICES-003. This device must be installed in a way where a
minimum 8" (20 cm) distance is maintained between users/bystanders and device.
6
®