IBM 5114 Maintenance Information Manual page 65

("'"
170
I/O INTERFACE CABLE PIN ASSIGNMENTS
. . POWER CONNECTOR
II
SIGNAL CONNECTOR
II
SIGNAL CONNECTOR
Pin Line Name
Pin Line Name Pin Line Name
(-"
..
1 Ground
' . , 1
+5 Vdc
Ground
2 +5 Vdc
2
-Put Strobe
2 +Osc/4
.
3
+5 Vdc
3 -Control Strobe 3 -Interrupt Req 2
4
+5 Vdc
4 -Get Strobe
4 +Bus Out P
5 +5 Vdc
5
+DA Y3 5
-Bus Out 0
6 Unused
6 +DA Y2 6 -Bus Out 1
7 Unused
7
+DA Yl 7
-Bus Out 2
C
8 Unused
8 +DA YO 8 -Bus Out 3
9 Unused
9 +DAX3 9
-Bus Out 4
10 Unused
10 +DAX2 10 -Bus Out 5
11 Unused
11
+DA Xl 11
-Bus Out 6
12
+8.5 Vdc
12 +DAXO 12 -Bus Out 7
13
+12 Vdc
13
Unused
13 Ground
14 -12 Vdc
14
Ground
14 Ground
15 -5 Vdc
15 +Op Code E 15 Unused
16
+Bus in P
16 Unused
. . SIGNAL CABLE
17 +Bus in 7 17 Unused
18
+Bus in 6 18 Unused
Pin Line Name
19 +Bus in 5 19 Unused
20
+Bus in 4 20 +Start Execute
B02 Unused
21 +Bus in 3 21 -Machine Check
B03 -Bus Out 7
22
+Bus in 2 22 + External Horz Drive
B04 -Bus Out 6
23 +Bus in 1 23 + Printer Clock
C~,
B05 -Bus Out 5
24 Unused 24 Unused
B06 -Bus Out 4
25 +Bus in 0 25 -Power On Reset
B07 -Bus Out 3
(see note 2)
B08 -Bus Out 2
B09 -Bus Out 1
II
SIGNAL CABLE
II
POWER CABLE
Bl0 -Bus Out 0
Bll
+Bus Out P
Pin Line Name Pin Line Name
B12 -Interrupt Req 2
B13
+Osc/4
B02 Unused B02 +5 Vdc
B03 +DAXO B03 +5 Vdc
D02 -Power On Reset (see note 2)
B04 +DAXl B04 Unused
D03 Unused (see note 1)
B05 +DAX2 B05 Unused
D04 + Printer Clock
B06
+DAX3
B06 Unused
D05 + External Horz Drive
B07 +DA YO B07 Unused
D06 -Machine Check
B08 +DA Yl B08
Unused
D07 +Start Execute Bit
B09 +DA Y2 B09 Unused
C'
D08 Ground
Bl0 +DA Y3 Bl0 Unused
D09 Unused
Bll -Get Strobe Bll +8.5 Vdc
Dl0 Unused
B12 -Control Strobe B12 +12 Vdc
Dll Unused
B13 -Put Strobe B13 Unused
D12 Unused
D13 Unused
D02
+Bus In 0
D02 +5 Vdc
D03 Unused D03 +5 Vdc
C\
D04 +Bus In 1 D04 +5 Vdc
Notes:
D05 +Bus In 2 D05 Unused
1. This line is grounded at the 5114
D06 +Bus In 3 D06 Unused
A1-Dl socket. A second 5114 uses
D07 +Bus In 4 D07 Unused
this signal to recognize its
D08 Ground D08 Unused
subdevice address.
D09
+Bus In 5
D09 Unused
2. 5114 generates a power on reset for
Dl0 +Bus In 6 Dl0 Unused
C
use by the 5103 Printer on second
Dll
+Bus In 7
Dll -5 Vdc
5114.
D12 +Bus In P 012 -12 Vdc
D13 +Op Code E
D13 Unused
Cable, Socket, and Pin Assignments 2-55