Advertisement
Quick Links
OWNERS MANUAL
SP12VSWP / SP24VSWP
Submersible Well Bore
DO NOT use any Submflsile pump for petrol/gasoline,
petroleum products.solve nts, thinners or ANY other
flammable liquid with flash point below 82 °(180 °F).
NOT FOR USE where flammable vapors are present.
Note:
BEFORE CONNECTING OR OPERATING
THIS PRODUCT, PLEASE READ THESE
INSTRUCTIONS COMPLETELY.
Pump
WARNING
Advertisement
Related Manuals for SCINTEX SP12VSWP
Summary of Contents for SCINTEX SP12VSWP
- Page 1 OWNERS MANUAL SP12VSWP / SP24VSWP Submersible Well Bore Pump WARNING DO NOT use any Submflsile pump for petrol/gasoline, petroleum products.solve nts, thinners or ANY other flammable liquid with flash point below 82 °(180 °F). NOT FOR USE where flammable vapors are present.
- Page 2 TABLE OF CONTENTS PAGE(S) INTRODUCTION COMPONENTS NEEDED FOR INSTALLATION PUMP CONNECTIONS & INSTALLATION INSTRUCTIONS PARTS LIST and REPLACEMENT PART KITS SUBMERSIBLE PUMP ASSEMBLY DRAWING BEFORE REQUESTING SERVICE "Helpful Hints" PUMP REMOVAL and DISASSEMBLY 9-10 PUMP RE-ASSEMBLY 11-13 APPLICATION WORKSHEET TECHNICAL SPECIFICATIONS 15-17 TOOLS REQUIRED FOR INSTALLATION &...
- Page 5 4) Hook-up Safety Line (Sling) (Fig. 7). ;; ; Safety line (Sling) should be CAUTION: M . . . � . . Corrosion resistant. a) Insert safety line (Part not included) through lift plate holes. b) Fasten line with appropriate connection approximately 1-2 ft (30 - 60 cm) above the pump.
- Page 6 PARTS LIST ITEM DESCRIPTION QUANTITY CABLE [NOT INCLUDED] INNER CABLE BOOT OUTER CABLE BOOT PLUG (CABLE ADAPTER) [NOT SHOWN] SCREW (PLUG) [NOT SHOWN] SCREW (LIFT PLATE) LIFT PLATE OUTLET FITTING 0-RING (OUTLET FITTING) 0-RING (LIFT PLATE) RECEPTACLE (CABLE ADAPTER) SET SCREW (RECEPTACLE) SCREW (MOTOR) FILTER SCREEN UPPER HOUSING...
- Page 8 BEFORE REQUESTING SERVICE "Helpful Hints" SYMPTOM PROBABLE CAUSE CORRECTION PUMP OPERAIBS but: 1) LOW VOLTAGE 1) CHECK POWER SUPPLY FOR PROPER VOLTAGE. NO FLOW REFER TO TECHNICAL SPECIFICATIONS (Pg. 16). FLOW REDUCED 2) NO WATER AT PUMP 2) MAKE SURE THE PUMP IS INSTALLED BELOW THE LOWEST ANTICIPATED WATER LEVEL.
- Page 9 II. PUMP REMOVAL AND DISASSEMBLY For servicing using Replacement Part Kits. Warnin g : Make sure all electrical p ower is off and the Hose ( Pi p e ) is not under p ressure. Warnin g : Canister ma y be p ressurised , disassemble the p um p in p ro p er order. Follow the manual directions carefull y .
- Page 10 7) Slide off the Filter Screen (Part M) (Fig. 10). 8) Remove the Canister (Part U) (Fig. 10). a) Using a 3/16" Allen Wrench remove the screws (Part V) from 3 places. b) Place one hand on the Upper Housing and the other on the Canister. Twist and pull the Assembly apart. 9) Remove Upper Housing (Part N) and Motor (Part T) (Fig.
-
Page 15: Specifications
TECHNICAL SPECIFICATIONS: MODEL NUMBER: SP12VSWP / SP24VSWP PUMP DESIGN: Positive Displacement 3 Chamber Diaphragm Pump CAM: 3.0 Degree MOTOR: Permanent Magnet, PIN 11-175-00 Thermally protected VOLTAGE: 12V 24 VDC Nominal WATTS: 120W AMPS: 12V 10.0MAX 24V 5.0 MAX FUSE: 7.5 AMP (Automotive) INTERNAL BYPASS: 130-150 P.S.I.
Need help?
Do you have a question about the SP12VSWP and is the answer not in the manual?
Questions and answers