Wiring Instructions; Maintenance; Troubleshooting - Ecco 7965 Series Installation And Operation Instructions Manual

Wiring Instructions:

Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is highly
recommended that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement
connectors (e.g., 3M Scotchlock type connectors).
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High
ambient temperatures (e.g., under-hood) will significantly reduce the current carrying capacity of wires, fuses, and circuit breakers. All wiring should
conform to the minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms,
grommets, cable ties, and similar installation hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect
these points from corrosion and loss of conductivity.
5. Ground termination should only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will "false trip" when mounted in hot environments or
operated close to their capacity.
Important: Disable power before wiring the beacon.
The wiring configuration is shown in Figure 3 below. All wiring should be a
minimum of 18AWG. A switch may be used to control the on/off function.
The black (negative) wire is connected to the battery ground.
(USER SUPPLIED)
FUSE (3 AMP)
(USER SUPPLIED)
(-)
(+)
GROUND
Figure 3
Flash Pattern Selection:
# Pattern FPM
1 Single 60
2 "R65" Single 120
3 Double 80
4 "R65" Double 122
5 Triple 75
6 Quad 75
7 "R65" Quad 122
8 Quint Hold 75
9 Pulse 8 75
10 Random N/A
11 Steady N/A
RED YELLOW
FLASH PATTERN SELECT
(ISOLATE WHEN NOT IN USE)
SWITCH
BLACK
GROUND
AMBER BLUE CLEAR
N/A N/A N/A
CLASS 1 CLASS 2 CLASS 1
CLASS 1 CLASS 1 CLASS 1
CLASS 1 CLASS 2 CLASS 1
CLASS 1 CLASS 2 CLASS 1
CLASS 1 CLASS 1 CLASS 1
CLASS 1 CLASS 2 CLASS 1
CLASS 1 CLASS 1 CLASS 1
CLASS 1 CLASS 1 CLASS 1
CLASS 1 CLASS 2 CLASS 1
N/A N/A N/A

Maintenance:

This LED beacon has been designed for trouble free operation. There are no
periodic maintenance needs for this model.

Troubleshooting:

1. Most beacon failures, including intermittent or erratic operation as well
as failure of operation can be traced to wiring or battery problems.
Check all wiring, connections, fuse, switch, and battery voltage to in-
sure that the correct voltage is reaching the beacon.
2. If this has not remedied the problem, return product to your local dealer
for warranty replacement, or call ECCO Customer Service for assis-
tance (800) 635-5900.
Note: Operating the vehicle without the lens installed on this product
will result in damage that will not be covered under warranty.
Flash Pattern Selection:
Flash patterns can be selected by touching the
yellow wire to the red power wire for less than a
second. Contacting the yellow and red wires for lon-
ger than a second toggles to the preceding flash
pattern.
GREEN RED
Replacement Parts & Accessories:
N/A N/A
Description
N/A N/A
Lens, 4"
N/A N/A
Lens, 6"
N/A N/A
N/A N/A Magnet Mount Kit
N/A N/A
Vacuum-Magnet Mount Kit
N/A N/A
Self Leveling Bracket
N/A N/A
Branch Guard
N/A N/A
Branch Guard
N/A N/A
Dust Cover
N/A N/A
Dust Cover
Vibration Dampening Kit
Black Top Decal
*where (X) indicates color:
Part Number
R6050LX*
R6070LX*
A6600MK
A6000VMK
A6600SLB
A6050BG
A6070BG
A6050DC
A6070DC
A6600VDK
A6501BT
A = Amber B = Blue
C = Clear G = Green
R = Red
Page 3 of 12