Advertisement
Quick Links
Advertisement
Related Manuals for dicodes 2380
Summary of Contents for dicodes 2380
- Page 1 2380 / 2380T manual...
- Page 2 It’s designed to use one or two stacked 18350, 18500, or 18650 batteries. The name 2380 stands for 23mm diameter and up to 80W of power. The headpiece has a slightly bigger diameter ring so that any atomizer in the range of 20 to 23mm fits perfectly onto the device.
-
Page 3: Display Operation
03 Display Operation The MOD is equipped with an OLED display which provides important status information after each vape. Temperature controlled mode: Battery-voltage at the end of Temperature at the end of vape the vape, including voltage Other modes: battery symbol drop during vape. - Page 4 (Re)set to Defaults...
- Page 5 05 Main Menu (Page 1) Power Up and Power Down Power Up increases power up to the “Power-Limit” value and then rolls over to 5W. Power Down decreases the power down to 5W and then rolls over to the Power-Lim value.
- Page 6 05 Main Menu (Page 2) Battery Status The Check Battery item shows the battery voltage (Ub0) and the battery voltage under load during the last puff (UbL). The difference is the voltage drop of the battery. A high drop (>0.4V) indicates a weak battery or contact problems. Please note that every battery has an inner resistance and the voltage at its contacts always drops when current is drained.
- Page 7 Note: If the power setting equals the power limit the boost has no function, as both values are the same. For a diagram of the boost operation options, please refer to the document “Explanations Referring to the Power Boost on dicodes Mods.” Commented [SC5]: Where is it located? Website url?
- Page 8 The possible error messages are: 0 OvrVolt: The input voltage is too high. The dicodes 2380 designed for the use of one or two batteries. If one battery is selected in the Extended Functions Stack Mode menu (Value=1) and the input voltage exceeds 4.5V “OvrVolt”...
- Page 9 (*1 ) The temperature coefficient is determined by the type of wire material, and must be within the range 100 to 650: 320=dicodes-wire, 620=Nickel, about 105=Stainless Steel, 350=Titanium (varying literature values, danger: fire hazard), 480=Tungsten (Wolfram). Value to select = Literature-value*10E5 K. Example: Ni 6.2E-3*1/K * 10E5*K => 620 (*2 ) Setting 1 (fastest) as 2 but without animation (visual shift effect), setting 5 (slowest) as 4, but without fast auto-repeat.
- Page 10 All dicodes devices allow the user to set the minimum discharge level of the battery between 2.5V and 3.0V (single battery, older models up to 3.5V). On the 2380 with the use of two batteries, the discharge level can be set between 6.2 to 6.8V. Almost all batteries specify a minimum discharge level of 2.5V to 2.7V.
- Page 11 Discharging 2380 batteries below 2.2V will destroy them. The 2380 can be used in 5 different modes. 3 of the 5 modes are only available when Expert-Mode is set to 1.
- Page 12 70mOhm) generates a power loss of just 3.5W distributed to two batteries! Moreover, the voltage drop is half as much. We recommend the following batteries for the dicodes 2380 and 2380T: Samsung INR18650 25R LG ICR18650 Hd2...
- Page 13 WEEE (waste electrical/electronical equipment). dicodes GmbH Friedrich der Große 70 DE-44628 Herne Germany Phone: +49 2323 1463635 Email: info@dicodes.de Errors excepted. Subject to changes without prior notice. c copyrights dicodes GmbH, Germany, no unauthorized reprint. 21.05.2015 dicodes 2380 Manual, ENG, revision 1...
Need help?
Do you have a question about the 2380 and is the answer not in the manual?
Questions and answers