Table of Contents
Advertisement
Quick Links
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip
Rev. 1.0
Assembly Instructions
FSP-01 FINE-SPRAY Pistol with Handgrip
Article Number:
Fig.: FSP-01 HD with regulating screw
NOTE
Please read the Assembly Instructions carefully before first using the incomplete device and
strictly adhere to the instructions!
The incomplete device may only be worked with and worked on by persons who are familiar
with the assembly instructions and the current regulations for industrial safety and accident
prevention.
Keep a translated version of the "Original Assembly Instructions" at the incomplete device!
F01-....
The instructions have to be available anytime!
Fig.: FSP-01 KLS and HVLP
Walther Systemtechnik GmbH – D 76726 Germersheim
phone: +49 (0)7274-7022-0 fax: +49 (0)7274-7022-91
http://www.walther-2000.de – info@walther-2000.de
Page 1 of 19
Advertisement
Table of Contents
Related Manuals for Walther FSP-01
Summary of Contents for Walther FSP-01
- Page 1 Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 1 of 19 Assembly Instructions FSP-01 FINE-SPRAY Pistol with Handgrip Article Number: F01-…. Fig.: FSP-01 HD with regulating screw Fig.: FSP-01 KLS and HVLP NOTE Please read the Assembly Instructions carefully before first using the incomplete device and...
-
Page 2: Table Of Contents
10.2.1 Spare Parts List for FSP-01 HD with Regulating screw ................18 10.2.2 Needles, Nozzles and Air Caps for FSP-01 HD with Regulating Screw ..........19 Walther Systemtechnik GmbH – D 76726 Germersheim phone: +49 (0)7274-7022-0 fax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de... -
Page 3: Ec Declaration Of Incorporation
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 3 of 19 EC Declaration of Incorporation in accordance with EU Machinery Directive 2006/42/EU, dated 17 May 2006, Appendix II B We herewith confirm that the below mentioned incomplete device meets the basic requirements for safety and health as stated in EU Machinery Directive 2006/42/EU for its design and construction as well as for the configuration released by us on the market. -
Page 4: Introduction
/ electronic residual energies. 2.3 Warranty and Liability According to the conditions laid down by the German Engineering Federation (VDMA), Walther Systemtech- nik GmbH has a guarantee of 12 months under normal European operating conditions on its own parts (spare parts are excluded);... -
Page 5: Correct Use
Page 5 of 19 2.4 Correct Use The FSP-01 FINE-SPRAY spraying pistol is designed and constructed for finest application of thin materials, e.g. release agents, colors or other fluids of low viscosity at room temperature. It is not suitable for spraying aggressive fluids such as acids, alkaline solutions, cleaning agents, chemicals, etc. -
Page 6: Transport
The type of packaging depends on the individual mode of shipping. If not separately contracted, the packaging is in accordance with the rules and regulations of Walther Systemtechnik GmbH. This rule is in accordance with the Federal Association for Packaging HPE. -
Page 7: Technical Data
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 7 of 19 4.2 Technical data KLS and HVLP Weight [g] approx. 240 Control air pressure [bar] max. 6 Material pressure [bar] max. 4 With Adjusting Screw Weight [g] approx. - Page 8 Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 8 of 19 Activate releasing trigger (19.1). Spray operation starts. You will notice that you receive so called “pre-air” prior to opening fluid flow when pulling the trigger. When releasing the trigger you still have “purging-air” after needle has closed nozzle and fluid flow was stopped.
-
Page 9: Taking Out Of Service
Before opening the spray valve it must be disconnected from the air and fluid supply. Otherwise, ejected components can cause injuries The FSP-01 Fine-Spray Pistols are high precision tools. Always keep clean and observe minimum instructions to maintain a long life of the valve. Always use clean and filtered material only. The control air must also be clean and should be slightly oiled, if necessary. -
Page 10: Cleaning
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 10 of 19 8.2 Cleaning Only use soft brushes for outside cleaning of the nozzle tips. Never use metal tools with sharp edges. Before starting any repair or maintenance work, make sure that the work place as well as the device itself are thor- oughly cleaned. -
Page 11: Spare Parts
9.1 General Information IMPORTANT First check all supply lines for connectivity and serviceability. In case of serious problems that cannot be resolved, please contact the Walther Systemtechnik GmbH cus- tomer service. 9.2 Cases of Failure Drops form on the trigger The needle gasket (10.1) is either worn or loose and must slightly be retightened. -
Page 12: Spray Image/ Type Of Defect
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 12 of 19 9.3 Spray Image/ Type of Defect SPRAY IMAGE PROBLEM CAUSE ACTION Normal Spray Image (Flat jet) Normal Spray Image (Round jet) Soiled Spray image shaped air cap... -
Page 13: Appendix
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 13 of 19 10 Appendix 10.1 Spare Parts Drawing for FSP-01 (KLS and HVLP) Walther Systemtechnik GmbH – D 76726 Germersheim phone: +49 (0)7274-7022-0 fax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de... -
Page 14: Spare Parts List For Fsp-01 (Kls And Hvlp)
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 14 of 19 10.1.1 Spare Parts List for FSP-01 (KLS and HVLP) Draw. No. Article No. Qty. Description 1.1.1 needle, stainless steel (part no. see overleaf) 2.1.1 nozzle, SM, stainless steel (part no. see overleaf) 3.1.1... -
Page 15: Needles, Nozzles And Air Caps For Fsp-01 (Kls)
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 15 of 19 10.1.2 Needles, Nozzles and Air Caps for FSP-01 (KLS) *needle KLS *nozzle KLS Draw No. Article No. Description Draw No. Article No. Description 1.1.1 97111074 needle 0.3mm 2.1.1... -
Page 16: Needles, Nozzles And Air Caps For Fsp-01 (Hvlp)
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 16 of 19 10.1.3 Needles, Nozzles and Air Caps for FSP-01 (HVLP) *needle *nozzle SM Draw No. Article No. Description Draw No. Article No. Description 1.1.1 97110073 needle 0.2/0.3mm 2.1.1... -
Page 17: Spare Parts Drawing For Fsp-01 Hd With Regulating Screw
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 17 of 19 10.2 Spare Parts Drawing for FSP-01 HD with Regulating Screw Walther Systemtechnik GmbH – D 76726 Germersheim phone: +49 (0)7274-7022-0 fax: +49 (0)7274-7022-91 http://www.walther-2000.de – info@walther-2000.de... -
Page 18: Spare Parts List For Fsp-01 Hd With Regulating Screw
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 18 of 19 10.2.1 Spare Parts List for FSP-01 HD with Regulating screw Draw. No. Article No. Qty. Description 1.1.1 needle, stainless steel (part no. see overleaf) 2.1.1 nozzle, stainless steel (part no. see overleaf) 3.1.1... -
Page 19: Needles, Nozzles And Air Caps For Fsp-01 Hd With Regulating Screw
Assembly Instructions - FSP-01 Fine-Spray Pistol with Handgrip Rev. 1.0 Page 19 of 19 10.2.2 Needles, Nozzles and Air Caps for FSP-01 HD with Regulating Screw *needle *nozzle Draw No. Article No. Description Draw No. Article No. Description 1.1.1 97110073 needle 0.2/0.3mm...