Audiolab LIVE 24 XL User Manual page 13

will automatically change to stereo pan. 22.
Link button Input channels, aux buses, can
be linked as a stereo pair. It will illuminate if
the stereo link button has been pressed and
enabled. The stereo pairs are predefined
and cannot be changed. They are as follows:
Channels 1 - 2 / Channels 3 - 4 / Channels 5
- 6 / Channels 7 - 8 / Channels 9 - 10 / Chan-
nels 11 - 12 / Channels 13 – 14 / Channels
15 - 16 / Channels 17 - 18 / Channels 19 - 20
Channels 21 - 22 / Channels 23 - 24 / Aux 1 - 2
/ Aux 3 - 4 / Aux5 - 6 / Aux7 - 8. A stereo link
can be enabled when either channel in the
pair is selected by pressing the Link button.
When the Link button is illuminated which
indicates the Stereo Link function enabled, all
DSP setting, solo status and main assignments
are passed to the other channel in the pair.
• Link & DCA: After link, the channels can
also be grouped to DCA as stereo chan-
nel, but not able to cancel the link in DCA.
On the contrary, if the channel has been
grouped to DCA, it can not link at all, but
its paired channel can link. For example,
channel 5 is linked with channel 6, then
both channel 5 and 6 can be grouped to
DCA. But if channel 5 has been grouped
to DCA first, it can not link to channel 6,
but channel 6 can link to channel 5.
• Link & Routing: The two linked channels
can route as stereo channel, while routed
channels can also link later. Please note
that this is a nondestructive passing, the
other channel's previous setting will be
restored after the Link button is disen-
gaged. For example, when Channel 6 has
been selected, then press Stereo Link
button, all of Channel 6's setting will be
copied onto Channel 5. The Channel 5's
own setting will restore after the Link
button has been disengaged.
30. Name Press this button to rename the chan-
nel. Operation: Press Name button--- Select
the channel which need to be named--- Edit
the name--- Enter.
31. DCA Clear Press this button to clear the
corresponding DCA group. Operation: Press
DCA Set button--- Select the DCA group
which need to be cleared--- Press DCA Clear
button--- Yes.
32. FX Mute This button is for FX function, when
press it, effects of FX1-2 will be mute syn-
chronously, which is similar to MUTE button.
33. DCA set Digital Control Audio (DCA) can re-
alize group assignment. DCA volume control
will always leave the same ratio between
the channel fader levels, independent of
the volume control. Press this button, it will
flash until some channels have been select-
ed, then press it again to save the settings
and turn off the button. For example, if you
want to set CH1 & CH2 as DCA1, the steps
are: Press DCA Set to enable DCA setting ---
Press DCA1, then select CH1 & CH2 --- Press
DCA Set again to confirm. The corresponding
window is as below picture show. For the
detail operation, please refer to introduction
of DSP Control section.
34. Meters Press this button to enter meters
check page, as below picture show, for the
details, please refer to corresponding intro-
duction of DSP Control section.
35. Talkback Insert the microphone on the rear
panel CH24 Mic input jack. Press this button
enter the Talkback interface and the button
will be illuminated at the same time. Touch
the Talkback Active box on the screen to
enable the Talkback function. CH24 can be
assigned to Main and AUX1-8. There are two
modes: PTT mode: Select PTT mode, you
must always press the Talkback button to
speak, and release to end the speaking. ON/
OFF mode: Select ON/OFF mode, press the
Talkback button to speak.
P. 13
- AUDIOLAB Live 24 XL
English version