Installation Environment - Siemens SIMOTICS S-1FL6 Installation Manual

s
motor can overheat resulting in fire and smoke. This can
result in severe injury or death. Further, excessively high
temperatures destroy motor components and result in
increased failures as well as shorter service lives of motors.
• Operate the motor according to the relevant
specifications.
• Only operate the motors in conjunction with effective
temperature monitoring.
• Immediately switch off the motor if excessively high
temperatures occur.
CAUTION
Burn injuries caused by hot surfaces
In operation, the motor can reach high temperatures, which
can cause burns if touched.
• Mount the motor so that it is not accessible in operation.
Measures when maintenance is required:
• Allow the motor to cool down before starting any work.
• Use the appropriate personnel protection equipment, e.g.
gloves.
1.2 Handling electrostatic sensitive devices (ESD)
Electrostatic sensitive devices (ESD) are individual components,
integrated circuits, modules or devices that may be damaged by either
electric fields or electrostatic discharge.
NOTICE
Equipment damage due to electric fields or
electrostatic discharge
Electric fields or electrostatic discharge can cause
malfunctions through damaged individual components,
integrated circuits, modules or devices.
• Only pack, store, transport and send electronic
components, modules or devices in their original
packaging or in other suitable materials, e.g conductive
foam rubber of aluminum foil.
• Only touch components, modules and devices when you
are grounded by one of the following methods:
- Wearing an ESD wrist strap
- Wearing ESD shoes or ESD grounding straps in
ESD areas with conductive flooring
• Only place electronic components, modules or devices
on conductive surfaces (table with ESD surface,
conductive ESD foam, ESD packaging, ESD transport
container).
1.3 Residual risks of power drive systems
Residual risks of power drive systems
When assessing the machine- or system-related risk in accordance
with the respective local regulations (e.g., EC Machinery Directive),
the machine manufacturer or system installer must take into account
the following residual risks emanating from the control and drive
components of a drive system:
1. Unintentional movements of driven machine or system
components during commissioning, operation, maintenance, and
repairs caused by, for example,
- Hardware and/or software errors in the sensors, control
system, actuators, and cables and connections
- Response times of the control system and of the drive
- Operation and/or environmental conditions outside the
specification
- Condensation/conductive contamination
- Parameterization, programming, cabling, and installation
errors
- Use of wireless devices/mobile phones in the immediate
vicinity of electronic components
- External influences/damage
- X-ray, ionizing radiation and cosmic radiation
2. Unusually high temperatures, including open flames, as well as
emissions of light, noise, particles, gases, etc., can occur inside
and outside the components under fault conditions caused by,
for example:
- Component failure
- Software errors
- Operation and/or environmental conditions outside the
specification
- External influences/damage
© Siemens AG 2018
3. Hazardous shock voltages caused by, for example,
- Component failure
- Influence during electrostatic charging
- Induction of voltages in moving motors
- Operation and/or environmental conditions outside the
specification
- Condensation/conductive contamination
- External influences/damage
4. Electrical, magnetic and electromagnetic fields generated in
operation that can pose a risk to people with a pacemaker,
implants or metal replacement joints, etc., if they are too close
5. Release of environmental pollutants or emissions as a result of
improper operation of the system and/or failure to dispose of
components safely and correctly
6. Influence of network-connected communication systems, e.g.
ripple-control transmitters or data communication via the
network
For more information about the residual risks of the drive system
components, see the relevant sections in the technical user
documentation.
NOTE
Protect the device, e.g. by installing it in a control cabinet with degree
of protection IP54 according to IEC 60529 or NEMA 12. Further
measures may be necessary for particularly critical operating
conditions.
If condensation or conductive pollution can be excluded at the
installation site, a lower degree of control cabinet protection may be
permitted.
1.4 Warning labels
Warning labels on servo motors
Do not exert any shock at the shaft end; otherwise, the encoder
may be damaged.
The surface temperature of the motor may exceed 80°C. Do not
touch the hot surfaces.
Warning labels in this document
Indicates that death, severe personal injuries or material
damages may result if proper precautions are not taken.
Indicates the actions that must not be performed.

2 Installation environment

Ambient temperature
• Operation: 0°C to 40°C
• Storage: -20°C to 65°C
Ambient humidity
• Operation: ≤ 90% RH (non-condensing
• Storage: ≤ 90% RH (non-condensing at
Operation altitude
≤ 1000 m
Vibration resistance
≤ 49 m/s
Note: When the surrounding
temperature is between 30 °C and
40 °C, the 1FL605❑ motors and
1FL609❑ motors with brake will have a
power derating of 10%.
at 30°C)
30°C)
2
A5E41599369-003