Table of Contents
Advertisement
The button head configuration was chosen
for operational considerations. The use of
other fastener types can increase the
potential for property damage and/or
personal injury.
B L A D E S A R E E X T R E M E LY S H A R P.
CONTACT WITH THE BLADE CAN RESULT
I N P R O P E R T Y D A M A G E A N D / O R
P E R S O N A L I N J U R Y. B L A D E S A R E
PROVIDED WITH A PROTECTIVE COVER
OVER THE CUTTING EDGE. EXERCISE
EXTREME CAUTION WHEN REMOVING
AND/OR REINSTALLING THE PROTECTIVE
COVER. STORE THE BLADE WITH THE
P R O T E C T I V E C O V E R P R O P E R L Y
INSTALLED TO MINIMIZE THE POTENTIAL
FOR BLADE DAMAGE AND/OR PERSONAL
INJURY.
7) Return the Bon Floor Stripper to its normal operat-
ing position.
8) Determine that the ON/OFF switch located on the
operator handle is in the OFF position. If the Bon
Floor Stripper is to be used immediately, then recon-
nect the extension cord or Bon Floor Stripper to the
power source.
UNEXPECTED MACHINE START UP CAN
RESULT IN PROPERTY DAMAGE AND/OR
PERSONAL INJURY.
Operation
OPERATIONAL DISCLAIMER.
THE MANUFACTURER OF THE BON FLOOR
STRIPPER MAKES NO WARRANTY OR
GUARANTEE THAT IT IS MERCHANTABLE
AND/OR SUITABLE FOR ANY SPECIFIC JOB
APPLICATION AND THAT IT WILL HAVE THE
CAPABILITY AND POWER REQUIRED TO
REMOVE ANY SPECIFIC COVERING FROM
ANY SPECIFIC WORK SURFACE.
C A L I F O R N I A P R O P O S I T I O N 6 5
DISCLAIMER.
THE DUSTS/BYPRODUCTS FROM THE
C O V E R I N G R E M O V A L P R O C E S S
ASSOCIATED WITH THE OPERATION OF
THE Bon Floor Stripper CAN CONTAIN
CHEMICALS KNOWN TO CAUSE CANCER,
B I R T H D E F E C T S , O R O T H E R
REPRODUCTIVE HARM.
I N F O R M AT I O N R E L AT I V E T O M I N I M U M
C O M P O N E N T S TA N D A R D S F O R T H E
OPERATION OF THE BON FLOOR STRIPPER.
For operational safety and overall productivity
considerations, it is required that specific Bon Floor
Stripper components meet minimum acceptable
operational standards BEFORE utilization:
1) Operator handle be properly mounted to the main
frame, with factory supplied ball-detent type retaining
pins that properly secure the handle to the main frame
while in the work position.
2) The operator handle is equipped with properly fit-
ting handle grips of sufficient integrity to allow for
proper job function as outlined within this manual.
Loose fitting handle grips or grips without full end
caps are not permitted.
3) An ON/OFF motor switch that allows it to perform
its intended job function as outlined within this
manual. Replace any damaged ON/OFF motor switch
with a factory approved replacement part only.
4) An extension cord and GFI that allows this accesso-
ry to perform its intended job function as outlined with-
in this manual. Replace any damaged extension cord
or GFI with a factory approved replacement part only.
5) Exciter plate elastomeric rubber mounts which
allow them to perform their intended job function as
outlined within this manual. Do not operate the BON
FLOOR STRIPPER without the correct number of
exciter plate elastomeric rubber mounts. Do not
operate the Bon Floor Stripper with a damaged and/or
improperly secured rubber mount. Replace any
damaged rubber mount with a factory approved
replacement part only.
6) Blade(s) and/or ceramic tile ripper attachment of
proper structural integrity (void of cracks, etc),
straightness, sharpness, etc which are retained by the
4430 Gibsonia Rd. • Gibsonia, PA 15044 • USA • www.bontool.com
18
Advertisement
Table of Contents
