Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for SPIDER X LINER
Summary of Contents for SPIDER X LINER
- Page 1 REMOTE CONTROLLED MOWER OPERATOR´S MANUAL SPIDER X LINER EDITION 1 – 2019 Product´s production number Engine type Engine´s production number DVOŘÁK – svahové sekačky s.r.o. Pohled 277, 582 21 Pohled, Czech Republic +420 564 036 099, info@spider-cz.com, www.slope-mower.com...
- Page 2 Operator’s Manual – Spider CROSS LINER Notes: 2 / 64...
-
Page 3: Table Of Contents
Operator’s Manual – Spider CROSS LINER TABLE OF CONTENT INTRODUCTION INSTRUCTIONS SERIAL NUMBER......................... 6 USING THE MANUAL ........................6 SAFETY ............................6 ABOUT THE PRODUCT GENERAL ............................. 8 MANUFACTURER ADDRESS ..................... 8 PRODUCT CONFORMITY ......................8 DECLARATION OF CONFORMITY ..................... 9 USE OF THE MOWER ....................... - Page 4 Operator’s Manual – Spider CROSS LINER 6.18 LUBRICATION ..........................56 6.19 TIRE PRESSURE ........................56 6.20 TIRE REPLACEMENT ........................ 56 6.21 MOWING HEIGHT ADJUSTMENT .................... 56 TECHNICAL DATA LIQUIDS, LUBRICANTS AND FILLING VOLUMES ..............57 TECHNICAL PLATE ........................57 TECHNICAL DATA ........................58 TROUBLESHOOTING MOWER TROUBLESHOOTING ....................
-
Page 5: Introduction
Operator’s Manual – Spider CROSS LINER INTRODUCTION Operating Instructions This manual is an integral part of the mower, keep it clean and in good condition. In case of loss or damage, replace it immediately. Always keep it available with the machine and, if handed over to another owner/operator, please provide the manual as well. -
Page 6: Instructions
/ similar type, as technical parameters, mower systems and controls may have changed. If you are unsure about any point, contact the manufacturer, SPIDER distributor/dealer or employer. Don't guess! You or someone else may be seriously injured or even killed. - Page 7 Operator’s Manual – Spider CROSS LINER GENERAL SAFETY Training Efficient and safe use of the mower includes your knowledge and skills. You must comply with all applicable laws, health and safety regulations in force in the country where the mower is being used. The operating instructions contain instructions on the mower, its controls and safe operation.
-
Page 8: About The Product
Product Conformity SPIDER XLINER was designed to comply with the laws and regulations in force at the time of its production for the market where it was first sold. In many countries, there are laws and regulations that require the owner to maintain the product within levels of compliance applicable to the product at its first place of the production. -
Page 9: Declaration Of Conformity
Product (Machine) – Type: Mower SPIDER CROSS LINER Výrobní číslo / Serial number: Sekačka SPIDER CROSS LINER je dálkově řízená sekačka určená pro sečení a Popis / Description: mulčování travnatých porostů na běžném i svažitém terénu. SPIDER CROSS LINER is a remote controlled mower designed for mowing and mulching grasslands on normal and sloping terrain. -
Page 10: Use Of The Mower
Operator’s Manual – Spider CROSS LINER USE OF THE MOWER The mower is designed to be used for mowing grasslands on flat and sloping terrain under normal conditions. The mower's work normally involves mowing or mulching while driving forward, backward and turning. -
Page 11: Figure 2 - Hazardous Zones
Operator’s Manual – Spider CROSS LINER PROHIBITED USE • The mower must not be used for any purpose other than that for which it is intended. • The mower must not be used on areas with glass particles, stones, iron or other unwanted objects that may be thrown by the rotating blade or which may damage the mower. -
Page 12: Figure 3 - Basic Description
Operator’s Manual – Spider CROSS LINER MAIN COMPONENTS LOCATIONS FUEL TANK CAP SAFETY BEACON FUEL TANK CAP BEZPEČNOSTNÍ MAJÁK CENTRAL STOP CENTRAL STOP INTAGRATED STABILIZING WINCH REMOTE CONTROL INTAGRATED STABILIZING WINCH REMOTE CONTROL Figure 3 – Basic description CENTRAL STOP... -
Page 13: Identification Of Components And Product
Operator’s Manual – Spider CROSS LINER IDENTIFICATION OF COMPONENTS AND PRODUCT MOWER The mower serial number is marked on the label located on the mower. ENGINE Important engine information and serial number can be found on the rear of the engine block. -
Page 14: Safety Labels
Operator’s Manual – Spider CROSS LINER SAFETY LABELS Safety labels are strategically placed around the perimeter of the product to remind you of potential risks. If you need reading glasses, you must wear them when reading safety labels. Do not overestimate your strength when reading safety labels. - Page 15 Operator’s Manual – Spider CROSS LINER Description Height of cut label Fuel label Safe operating distance Danger of being hit by flying objects No manipulation with moving parts until the whole system is stopped Warning, do not use your hands as protection...
- Page 16 Operator’s Manual – Spider CROSS LINER Correct winding direction of the rope Wrong direction for rope winding When winding / unwinding, keep the rope tightened Read the manual before handling Risk of dragging fingers and hand palm into the machine...
-
Page 17: Remote Radio Controller
Operator’s Manual – Spider CROSS LINER REMOTE RADIO CONTROLLER CENTRAL STOP Two red colored CENTRAL STOP buttons are used to switch the mower off. One is located on the mower (1), the other on the remote control (RC) (2). 1 – CENTRAL STOP on the mower 2 –... - Page 18 Operator’s Manual – Spider CROSS LINER ACTIVATION SWITCH SKID ACTIVATION STEERING SWITCH MAIN SKID CONTROLLER STEERING SWITCH MAIN SWITCH CONTROLLER BATTERY The controller´s battery is shown in the figure. Remove the battery from the controller to recharge it. CONTROLLER CONTROLLER...
-
Page 19: Operation
Operator’s Manual – Spider CROSS LINER OPERATION The aim of this handbook is to guide the operator get familiarized, step by step with the use of the mower so that it can work efficiently and safely. Read the OPERATION chapter from start to finish. - Page 20 This mower is designed to work under normal outdoor atmospheric conditions. It must not be used in confined spaces without adequate ventilation. Do not use the mower in potentially explosive atmospheres, ie with explosive vapors, gases or dust, without consulting with your Spider distributor / dealer. Regulations Comply with all laws and local labor requirements applicable to you and the mower.
- Page 21 After assessing any occupational hazards, the operator must comply with all safety requirements. If you are uncertain about the use of the mower on a particular job, please contact your local SPIDER distributor / dealer who will be happy to provide you with the necessary information. Below is an example of some aspects that need to be taken into account in the risk assessment.
-
Page 22: Mower Check Up
Operator’s Manual – Spider CROSS LINER Workspace • Does the ground have enough bearing capacity? • How rough is the terrain? Are there sharp projections on the ground that could damage the mower and especially its tires? • Are there obstacles in the area, such as potholes, hidden debris, wood, tree stumps, stones, wires, glass and other similar objects? •... -
Page 23: Before Starting The Engine
Operator’s Manual – Spider CROSS LINER BEFORE STARTING THE ENGINE WARNING Before starting the engine, a check-up of the mower must always be performed. This is important both in terms of safety (yours and others) as well as to ensure maximum durability of the mower. -
Page 24: Stopping And Parking
Operator’s Manual – Spider CROSS LINER STOPPING AND PARKING WARNING An incorrectly parked mower may spontaneously move in the absence of the operator. Follow the instructions in the operating instructions for proper parking methods. Stop the mower on dry and level ground, where the mower will not pose a risk and / or danger. -
Page 25: Mower Safety Elements
Operator’s Manual – Spider CROSS LINER WARNING The CENTRAL STOP buttons on the controller and on the mower should be used whenever an emergency stop is required. See also: REMOTE RADIO CONTROLLER > CENTRAL STOP MOWER SAFETY ELEMENTS When driving, always keep the mower under control. It is necessary to pay attention to any obstacles and always watch out for potentially dangerous situations. - Page 26 SPIDER MODE The mower is equipped with a unique SPIDER mode control system (also known as the “dance step”), thanks to which all 4 wheels turn at full 360 °, so there is no need to rotate the machine if you need to change direction.
-
Page 27: Cutting Blade On/Off
Operator’s Manual – Spider CROSS LINER CUTTING BLADE ON/OFF To switch on the cutting deck, set the blade on / off switch to ON. To turn off the cutting deck, set the blade on / off switch to OFF. MOWING BLADE ON / OFF SWITCH ZAPNUTÍ... -
Page 28: Hydraulic Stabilizing Winch
IT IS FORBIDDEN TO USE THE WINCH • If any parts of this equipment are damaged or show considerable wear, e.g.: rope, carabiner, etc. • For purposes other than stabilizing the SPIDER XLINER. • For removing objects, securing people or objects on a slope. •... -
Page 29: Figure 8 - Main Components Of The Hydraulic Winch
Operator’s Manual – Spider CROSS LINER WHILE WORKING WITH THE MOWER YOU SHOULD AVOID: • sudden sharp steering or braking • driving too fast • unstable soil • driving on uneven surfaces • changing wheel adhesion (driving from areas exposed to sun to shade etc.) •... - Page 30 Operator’s Manual – Spider CROSS LINER WORKING WITH THE WINCH The winch is a device, which extends and improves the mower application possibilities. Please keep in mind, it does not allow the operator to use the mower on all slope inclines.
-
Page 31: Figure 9 - Methods Of Mowing On The Slope With Use Of The Winch
Operator’s Manual – Spider CROSS LINER MOWING WITH THE USE OF WINCH WARNING Driving on slopes is very demanding for an operator, as he hast to constantly evaluate information on the movement of the machine and the character of the terrain. Especially important is the wheel adhesion to the grass or other surface and the angle of the mower. -
Page 32: Mower Transportation
Operator’s Manual – Spider CROSS LINER EMERGENCY SITUATIONS WHEN WORKING ON THE STABILIZING WINCH EMERGENCY SITUATION RECOMMENDED SOLUTIONS Turn the wheels immediately so that they are perpendicular to the slope (across to A rope or anchor is suddenly the slope), stop the movements. Find a new anchor point. Press the STOP button released on the remote control. -
Page 33: Operating Conditions
Operator’s Manual – Spider CROSS LINER Make sure that the ramps have enough load capacity. The load capacity must correspond with the weight of the mower listed on the production plate. Do not allow any person to stand on or close to the ramps when loading. -
Page 34: Rerueling The Machine
Operator’s Manual – Spider CROSS LINER OPERATION IN DUSTY OR SANDY AREAS • Check the air filter regularly, clean or replace the relevant parts as needed, regardless of the inspection interval. • Tighten the hydraulic tank filler cap tightly to prevent sand and dust from entering the hydraulic system. See MOWER MAINTENANCE PLAN •... -
Page 35: Storage
Operator’s Manual – Spider CROSS LINER STORAGE CLEANING WARNING When using cleaning liquids, solvents or other chemicals, you must follow the manufacturer's instructions and precautions. WARNING Wear protective gloves when handling hot parts to prevent burns. To protect your eyes, wear eyeglasses when cleaning parts with a wire brush. - Page 36 Operator’s Manual – Spider CROSS LINER SEASON PREPARATION 1) Check all fluid levels. If necessary, top off to the recommended level. 2) Clean the mower and remove any unwanted material and corrosive products. Dry the mower to remove solvents and moisture.
-
Page 37: Maintenance
DVOŘÁK – svahové sekačky s.r.o. spare parts catalog has been prepared in the partner zone website, where you will find individual spare parts and aids that you can order from your local Spider dealer for your mower type. When ordering spare parts, you must tell our representative exactly the model of the mower and its serial number. -
Page 38: Maintenance Safety
Operator’s Manual – Spider CROSS LINER MAINTENANCE SAFETY Compressed air Compressed air is dangerous. Always wear personal protective equipment. Never aim the compressed air nozzle at yourself or others. Springs Always wear personal protective equipment when removing assemblies containing spring-loaded components. This will protect you from potential eye injuries caused by flying parts. - Page 39 Operator’s Manual – Spider CROSS LINER WASTE DISPOSAL WARNING It is forbidden to pollute bodies of water, sewers or soil. Remove all spills and / or lubricants. Used lubricant fluids, filters and contaminated materials must be disposed in accordance with local regulations.
-
Page 40: Maintenance Schedule
Operator’s Manual – Spider CROSS LINER First Aid – Oil Eyes If you get oil in your eyes, it should be washed with water for about 15 minutes. If irritation persists afterwards, seek medical attention. Ingestion If you accidentally swallow oil, do not try to induce vomiting. Check with your doctor. - Page 41 Operator’s Manual – Spider CROSS LINER MOWER MAINTENANCE CHART X = Operator S = Authorized service * = in dusty condition to be performed more often Visually check for oil leakage from engine and hydraulic systems Check the tire pressure...
-
Page 42: Vertical Service Position
Operator’s Manual – Spider CROSS LINER VERTICAL SERVICE POSITION It is possible to place the mower in a vertical service position for cleaning and maintenance of the mower deck. It is only allowed to turn the mower into this position on a firm and level surface for the time necessary for service. -
Page 43: Service Points
Operator’s Manual – Spider CROSS LINER SERVICE POINTS ENGINE AREA OIL CAP WITH DIPSTICK SPARKING PLUG DRAIN PLUG ELECTRIC STARTER SILENCER Image 11 - Service points - internal combustion engine SERVICE POINTS - Mower HYDRAULIC SYSTEM STABILIZING WINCH HYDRAULIC SYSTEM... -
Page 44: Access Points
Operator’s Manual – Spider CROSS LINER ACCESS POINTS Before putting the mower into operation, ensure that all access panels are correctly in their closed or installed position. ENGINE COVER WARNING Dust particles in the air or light combustible material (e.g. straw, grass, sawdust, etc.) must not accumulate in the engine and exhaust compartment. -
Page 45: Geometry Adjustment
Operator’s Manual – Spider CROSS LINER GEOMETRY ADJUSTMENT GEOMETRY CHECK The geometry is adjusted mechanically. The mower operator evaluates whether the geometry needs to be adjusted or not. Figure 13 – Geometry check GEOMETRY ADJUSTMENT If you do not have the necessary equipment and experience, have the work done by a specialized service center. -
Page 46: Engine
Operator’s Manual – Spider CROSS LINER ENGINE ENGINE MAINTENANCE PLAN The activities listed below are considered workshop maintenance and should only be performed by trained personnel. Before starting any maintenance work on the mower, switch off the engine and allow it to cool down, press the CENTRAL STOP emergency button on the mower and remove the key. -
Page 47: Engine Air Filter
Operator’s Manual – Spider CROSS LINER Engine Oil Level Check: 1) Ensure that the mower is on a level surface 2) Stop the engine and allow it to cool down. 3) Open the bonnet and pull out the dipstick. 4) Wipe the dipstick with a clean cloth and push it back into the inspection hole as far as it will go. -
Page 48: Fuel System
Operator’s Manual – Spider CROSS LINER CLEANING 1) Unscrew the wing nut from the air filter cover and remove the cover. 2) Pull out the filter elements. 3) Pull the foam filter cartridge out of the paper filter cartridge. 4) Inspect both filter elements and replace if damaged. Change the paper filter cartridge according to the maintenance schedule. -
Page 49: Mowing Blade
Operator’s Manual – Spider CROSS LINER 5.10 MOWING BLADE Check the condition of the blade regularly. THE BLADE: • Cannot bear traces of damage such as bending, or other deformations. • It must be securely fastened to the flange with fixing screws. -
Page 50: Hydraulic System
Operator’s Manual – Spider CROSS LINER GRINDING AND INSPECTION OF THE CUTTING BLADE To check the blade geometry: - the blade must not be bent - Never straighten a bent blade, USE NEW! - the ends of the knife must be flush (test whether the whole surface is on a flat surface)) -
Page 51: Hydraulic Stabilizing Winch
Operator’s Manual – Spider CROSS LINER 5.12 HYDRAULIC STABILIZING WINCH ROPE MAINTENANCE Before each shift, check the condition of the rope, especially if you have been working in terrain where unwanted objects, sharp edges, etc. were present. After 20 hours of operation, pull the entire rope out of the winch and check its condition thoroughly for any damage. -
Page 52: Electrical System
Operator’s Manual – Spider CROSS LINER 5.13 ELECTRICAL SYSTEM INSPECTION (OPERATION) Make sure the entire electrical equipment works properly. All defective parts must be repaired before use. CHARGING THE RC BATTERY 1. Slide the battery from the controller 2. Connect the charger to the car cigarette lighter socket. -
Page 53: Neutral Position Adjustment
Operator’s Manual – Spider CROSS LINER HOW TO CONNECT THE BATTERY 1) Ensure safe operation of the mower 2) Arrange access to the battery. 3) Connect the battery terminals. Connect the ground terminal (-) last. 4) Secure the battery against movement using a tie-down strap BATTERY TESTING The best and easiest way to test the battery is to use a voltmeter or a multimeter to measure the resting voltage. -
Page 54: Wheel Suspension
Operator’s Manual – Spider CROSS LINER INSPECTION 1) Ensure safe operation of the mower. 2) Arrange access to the belts. 3) Check the belt tension with a slight thumb pressure between the pulleys. 4) If the belt is loose, have the belt tensioned or replaced by a specialized service center. -
Page 55: Drives Inside Of The Chassis Wings
Operator’s Manual – Spider CROSS LINER WARNING Never reach into the inner parts of the wheel suspension. Have any work carried out by an authorized service center. 5.17 DRIVES INSIDE OF THE CHASSIS WINGS WARNING Make sure the engine is switched off before checking the drive. Before checking, remove the key from the CENTRAL STOP button on the mower. -
Page 56: Lubrication
Operator’s Manual – Spider CROSS LINER 5.18 LUBRICATION Apply a reasonable amount of lubricant to the parts to be lubricated. Excessive amounts of lubricant cause leakage and contamination of the mower and the environment. Insufficient quantity requires more frequent lubrication and can lead to damage. -
Page 57: Technical Data
Operator’s Manual – Spider CROSS LINER TECHNICAL DATA LIQUIDS, LUBRICANTS AND FILLING VOLUMES WARNING In the event of any unauthorized fuel types (or their equivalents) being used at any time, the producer rejects any liability for engine failure. Item Liquid/Lubricant... -
Page 58: Technical Data
Operator’s Manual – Spider CROSS LINER TECHNICAL DATA The mower is a self-propelled all-wheel-drive machine controlled by a remote control. Parameter Measure Value 980 × 1110 × 600 Dimensions (l x w x h) Mowing width Height of cut 45–110... -
Page 59: Troubleshooting
Operator’s Manual – Spider CROSS LINER TROUBLESHOOTING MOWER TROUBLESHOOTING Failure Probable cause Repair Discharged battery Recharge the battery, check the fuse Disconnected battery Connect the clamps Electricity wire disconnection Check/exchange harness Spark plug doesn’t work Clean / replace the spark plug... -
Page 60: Winch Troubleshooting
Operator’s Manual – Spider CROSS LINER WINCH TROUBLESHOOTING Failure Probable cause of failure Repair The drum is not rotating Lack of oil in the hydraulic system of the machine Add hydraulic oil Jerking motion of the drum Lack of oil in the hydraulic system... - Page 61 Operator’s Manual – Spider CROSS LINER Control start up, the green LED is off the red LED has THREE long blinks³. At Radio Remote The SAFETY command is Bring the actuators to the rest activated position. Control start up, the green LED is off the red LED¹...
-
Page 62: Warranty Conditions
(“Spider”) to the original purchaser of new equipment from Spider or authorised Spider Distributors/Dealers. Under these warranties Spider will repair or replace, at its opinion, any covered parts which is found to be defective in material or workmanship during the applicable warranty term. Warranty service must be performed by a Distributor/Dealer or service centre authorised by Spider to sell and/or service the type of equipment involved, which will use only new or remanufactured parts or components furnished by Spider. - Page 63 The selling Distributor/Dealer has no authority to make any warranty, representation, condition or promise on behalf of Spider, or to modify the terms or limitations of this warranty in any way and makes no warranty on any other item unless it delivers to the purchaser a separate written certificate specifically warranting the item.
- Page 64 Operator’s Manual – Spider CROSS LINER Shortcuts: RRC (RC) Radio Remote controller Mower Spider XLINER Figures: Figure 1 – Maximum slope Figure 2 – Hazardous zones Figure 3 – Basic description Figure 4 – Basic description Figure 5 – Identification of the mower Figure 6 –...
Need help?
Do you have a question about the X LINER and is the answer not in the manual?
Questions and answers