Advertisement
EXCESS RIPPLE DETECTED
One or more diodes in the alternator are not functioning or
there is stator damage. check to ensure the alternator
mounting is sturdy and that the belts are in good shape and
functioning properly. If the mounting and belts are good,
replace the alternator.
4.8.10.
Press the «ENTER» key to continue the charging system with
accessory loads. One of the three results will be displayed
along with the actual testing measured.
CHARGING SYSTEM HIGH WHEN TESTED WITH
ACCESSORY LOADS
The voltage output from the alternator to the battery exceeds
the normal limits of a functioning regulator. check to ensure
there are no loose connections and that the ground connection
is normal. If there are no connection issues, replace the
regulator. Since most alternators have the regulator built-in,
this will require you to replace the alternator.
CHARGING SYSTEM LOW WHEN TESTED WITH
ACCESSORY LOADS
The alternator is not providing sufficient current for the
system's electrical loads and the charging current for the
battery. check the belts to ensure the alternator is rotating
with the engine running. If the belts are slipping or broken,
replace the belts and retest. check the connections from the
alternator to the battery. If the connection is loose or heavily
corroded, clean or replace the cable and retest. If the belts
and connections are in good working condition, replace the
alternator.
CHARGING SYSTEM NORMAL WHEN TESTED WITH
ACCESSORY LOADS
The system is showing normal output from the alternator.
No problem detected.
4.9.
SETTINGS AND INFORMATION RETRIEVAL
4.9.1.
LANGUAGE SELECTION
4.9.1.1.
connect the tester to a battery.
4.9.1.2.
The tester defaults to the bATTERY TEST display. Press the
directional keys to the lANGuAGE SElEcT display.
4.9.1.3.
Press ENTER and the display will show the language options.
Press the directional keys to select the language you want the
tester to display.
4.9.1.4.
Press ENTER and the display returns to bATTERY TEST.
5. MAINTENANCE
5.1.
clean tester with a damp soft cloth DO NOT use solvents.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey limited
www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500
Environmental Protection
Sole uK Distributor, Sealey Group.
Kempson Way, Suffolk business Park,
bury St. Edmunds, Suffolk.
IP32 7AR
Original Language Version
RIPPlE DETEcTED
XX.XXV
HIGH
AlT. lOAD VOlTS
XX.XXV
AlT. lOAD VOlTS
XX.XXV
AlT. lOAD VOlTS
XX.XXV
NORmAl
WEEE Regulations
01284 757500
01284 703534
HIGH
lOW
www.sealey.co.uk
Web
sales@sealey.co.uk
bT2014 | Issue:1 01/06/17
Advertisement
