Nibe Contura 655 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Nibe Manuals
  4. Stove
  5. Contura 655
  6. Installation instructions manual
Nibe Contura 655 Installation Instructions Manual

Nibe Contura 655 Installation Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SE
DE
NO
GB
Contura 655
Contura 655/685
Installationsanvisning
Installationsanleitung
Installasjonsanvisning
Installation Instructions
511836
IAV SE 0715-2
2
16
32
48

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Contura 655 and is the answer not in the manual?

Questions and answers

Related Manuals for Nibe Contura 655

Summary of Contents for Nibe Contura 655

  • Page 1 511836 IAV SE 0715-2 Installationsanvisning Installationsanleitung Installasjonsanvisning Installation Instructions Contura 655 Contura 655/685...

  • Page 2: Table Of Contents

    Connection to the chimney ......54 Installing the surround Contura 655 ..... . .55 Installing the surround Contura 685 .
  • Page 3 Distance to cumbustible wall (mm): Behind 100 Beside 520 (200) Corner 95 Production number: 7090300236 Follow the installation instructions. Use only recomended fuels NIBE AB Box 134 SE-285 23 MARKARYD SWEDEN CONTURA Type: 600-series Production no. 7090300236 NIBE AB SE-85 21 Markaryd Sweden...

  • Page 4: General

    General Structural support This manual contains instructions about how the Check.to.make.sure.that.the.floor.is.strong.enough. Contura 655/685 must be constructed and installed. to. support. the. weight. of. the. stove. and. chimney .. If. Instructions for lighting and use are also supplied you.intend.to.locate.the.stove.on.standard.wooden. with the stove. Read them carefully and keep them floor.

  • Page 5: Installation Distance To Walls And Ceiling

    Installation distance from walls and ceiling. Position the stove on a hearth plate and check that that steel flues require. the installation distances given in the diagrams are The minimum distance between the stove opening met. When top connecting a steel flue please refer to and combustible parts of the building or décor must the relevant manufacturer’s installation instructions.

  • Page 6: Supply Of Combustion Air

    Supply of combustion air Combustion air can be provided directly via a duct from outside, or indirectly via a vent in the outer wall of the room where the stove is to be placed. Some installation alternatives are shown to the right. When installing the supply air hose on the air inlet, the heat deflector panel must be installed under the insert.

  • Page 7: Unpacking

    Unpacking Leave the insert screwed to the pallet. Place accompanying parts to one side. Remove the loose parts from the insert, i.e. the fire bars, cladding, grate plate and ash-pan. Then remove the insert from the pallet. Important! The insert may tip forward before the base plate is installed.

  • Page 8: Connection To The Chimney

    Connection to the chimney Refer to the chimney’s installation instructions to install the chimney. The following describes how the chimney is connected to the stove. The insert is prepared for top connection at delivery. When connecting from the rear, the cover and connection must be swapped around.

  • Page 9: Installing The Surround Contura 655

    Installing the surround Contura 655 Important! The heat deflector panel under the insert Place the back of the insert on the pallet. Install the base with the four Allen screws; screw them must be installed in case the space is used for wood into place from the inside of the legs in the base’s...
  • Page 10 Hold the side panel approximately 20 mm above Use crosshead screws with washers to secure the the base panel and turn the side panel’s front edge side panels. Adjust the side panels so that they lie around the edge of the leg. Align and depress the against the insert at the front edge and against the side panel end over the base panel’s shaft pin.

  • Page 11: Installing The Surround Contura 685

    Installing the surround Contura 685 Unpack the column kit. On the reverse of the column there is a removable cover, this is used when installing the combustion air connection. Place the insert with the back on the pallet and unscrew the eight screws for the support legs. Remove the support legs and the heat deflector panel and install the column with the four screws.
  • Page 12 The front angle irons are installed with two crosshead screws each. The rear angle irons are installed with crosshead screws and nuts in the inner hole on the firebox. Install the back panel between the mountings in the stove using four sheet metal screws. Tap out the knockout from the back panel at the rear connection using a hammer.
  • Page 13 Place the insert on the hearth plate and check the installation distance. Connection to the chimney from the back on the insert must be carried out before installing the steel sides. When top connecting to the chimney, the steel sides must be installed first. Remember to install the hot air grille before top connecting. Secure the steel sides on the angle irons at the top edge.

  • Page 14: Installing The Oven (Option)

    Installing the oven (option) Remove the screw on the top hinge of the door. Hold the oven door in place on the threaded pin. Replace this screw with the threaded hexagonal pin. Hook the upper hinge into place and lightly tighten This pin serves as the lower hinge for the oven door.

  • Page 15: Installing The Convection Front (Option)

    Installing the convection front (option) Open the door and install the convection front with First insert the convection front so that the sprung the suspended mountings pointing as illustrated. catch is in front of the front panel on the stove and press the convection front upwards gently.

  • Page 16: Installing The Stove Top

    Installing the stove top Place the soapstone top (or plate top, cast iron top) in position. Handle soapstone with care. Place the hot air grille and cover on the soapstone top. Important! Before the stove is used, it must be inspected by an authorised chimney sweep. Read the ”Instructions for lighting and maintenance Contura 600 series”, before lighting for the first time.

  • Page 17: Installing The Drawer (Option)

    Installing the drawer (option) Important! When.installing.the.drawer,.the.knockout.in.the. back.panel.must.always.be.removed.for.the. supply.of.convection.air . Slacken. off. the. rear. Allen. screw. three. turns .. Place. the.pull-out.unit.on.the.base.panel . Hook. the. pull-out. unit. over. the. rear. Allen. screws .. Install.the.drawer.on.the.pull-out.unit.using.the.four. Screw.in.the.unit . Allen.screws ..Adjust.the.drawer.so.that.it.is.centrally. positioned,.then.tighten.the.screws ..
  • Page 20 NIBE AB/NIBE Brasvärme Box 134 SE-285 23 Markaryd, Sweden • • www.contura.eu...

This manual is also suitable for:

Contura 685

Table of Contents