Page 2
WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. For the customers in the USA This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Page 3
Ce produit est prévu pour être utilisé dans l’environnement électromagnétique suivant: E4 (environnement EMC contrôlé ex. studio de télévision). Periodic inspections To guarantee safe long-term operation, periodic inspections are recommended. Please contact your Sony representative for detailed information about the content and cost of periodic inspections.
Overview The DVS-9000-C or DVS9000SF-C Switcher Processor Pack is a high-performance, multi-function production switcher processor for use in an SDTV-format DVS-9000 video switcher system. It has a wide range of application, being usable in studios and the ENG and OB vans of large- scale live production systems as well as in postproduction editing systems.
Page 6
DVS-9000SF Production Switcher Processor DVS-9000SF Production Switcher Processor main unit. This is the main chassis unit of the DVS-9000SF Production Switcher Processor (size EIA 4RU). It is supplied with boards for 1 M/E banks, 17 inputs, and 12 outputs as standard equipment.
Sony service representative. Note If a status indicator does not light when you turn a POWER switch on, there may be a fault in the power circuits. Turn the POWER switch off and contact your Sony service representative. POWER A POWER B...
DVS-9000 Rear Panel 1SWITCHER REMOTE 1 to 4 connectors 2SWITCHER CTRL connector 3 EXT connector 4REF OUT connector 5SWITCHER DATA connector 6REF IN connectors 7DME EXT IN 1 to 4 connectors qjOUTPUTS 1 to 48 connectors qkPRIMARY INPUTS 1 to 68 connectors qlEXTEND INPUTS 69 to 80 connectors w;MONITOR OUTPUTS 49 to 56 connectors Location and Function of Parts...
Page 9
* For information about Ethernet switches that can be used in an DVS-9000 system, contact your Sony service representative. * Ethernet is a trademark of XEROX Corporation. For more information about Ethernet switch connectors, see “DVS-9000 System Configuration”...
Page 10
In that case, the AC IN C and D connectors is not used. Caution For information about installing an HK-PSU04, contact your Sony service representative. q OUTPUTS 1 to 48 connectors (BNC type) (BKDS-9160) These connectors output serial digital signals. They can be freely assigned to program output, preview output, AUX output and so on.
Sony service representative. Note If a status indicator does not light when you turn a POWER switch on, there may be a fault in the power circuits. Turn the POWER switch off and contact your Sony service representative. POWER A POWER B...
REMOTE 3 TERMINAL * For information about Ethernet switches that can be used in an DVS-9000 system, contact your Sony service representative. For more information about Ethernet switch connectors, see “DVS-9000 System Configuration” (page 15). For detailed information about setting up the Ethernet switch, refer to the documentation supplied with the Ethernet switch.
Page 13
SWITCHER REMOTE 1 to 4 connectors (D-sub 9-pin, RS-422A) Used to control the DVS-9000SF AUX bus from external devices, and to operate the DVS-9000SF from editing control systems such as the BVE-9100. Specify the types of connected devices on the center control panel.
Page 14
r OUTPUTS 1 to 24 connectors (BNC type) (BKDS-9162) These connectors output serial digital signals. They can be freely assigned to program output, preview output, AUX output and so on. There are two BNC connectors for the lower numbers on each slot (1 to 4, 13 to 16) and one BNC connector for the upper numbers (5 to 12, 17 to 24) (the BKDS-9162 is required 13 to 24).
Example System Configuration DVS-9000 System Configuration The figure below shows the configuration of a DVS-9000 system. Ethernet switch Ethernet switch REMOTE DATA CTRL SWITCHER DATA SWITCHER CTRL EXT IN MONI OUT DATA CTRL REMOTE REF IN DATA CTRL REMOTE 2 REMOTE 1 REF OUT REMOTE 4...
“Accessories not supplied” (page 18). b) Terminate with the supplied 75 terminators. Terminators are supplied in the product package. Example System Configuration The flow of signals is the same in a DVS-9000SF system. DME EXT IN DME MONI OUT 1 - 4...
Power Supply Unit Status Indicators The power supply unit status indicators show the status of the power supply unit during operation and when the unit is powered on. Whenever a power error is detected, it is reflected immediately by the indicator. Meaning of status indicator displays Indicator Status...
Specifications The following specifications show the reference performance for this unit and individual option boards/ modules. Design and specifications are subject to change without notice. DVS-9000 Production Switcher Processor General Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 8.5 A, 240 V: 4.2A Peak inrush current (1) Power ON, current probe method:...
DVS-9000SF Production Switcher Processor General Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 100 V: 5.4 A, 240 V: 2.5 A Peak inrush current (1) Power ON, current probe method: 60 A (100 V), 110 A (240 V)
CN board: 274×94 mm ×3 inches) (using 2 boards) Mass Approx. 2 kg (4 lb 6 oz) Output Outputs 24 (BNC type), 1 to 4 and 13 to 16, each with 2 outputs Signal format SMPTE259M-C Signal level 0.8 Vp-p 10% Signal transfer rate 270 Mbps Accessories supplied...
Relay contact outputs: 4 (30V AC/DC, 0.1A) Open collector outputs: 4 Input Inputs 4 (BNC type) Signal format SMPTE259M-C Signal level 0.8 V p-p 10% Signal tansfer rate 270 Mbps Return loss 15 dB Cable length 200 m (5C-2V cable, BELDEN8281 or equivalent) Output Outputs...
Page 23
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any...