Advanced Remote Operations
Operating One Component
While Using Another
(background operation)
You can temporarily operate other components while
listening to or watching a program.
SLEEP
LEARN
SYSTEM CONTROL / FUNCTION
VIDEO 1
VIDEO 2
VIDEO 3
(AUTO CATEGORIZE SYSTEM)
TAPE
DAT/MD
TV
CONTROL
1
ON
4
7
BACK
GROUND
SHIFT
BACKGROUND
>
10
–
+
SUB CH
POSITION
0
)
=
— RMS —
DIRECTION
CLEAR
9
(
— SOUND FIELD —
ON/OFF
GENRE
MODE
EQ/
TONE
BAND
SLOPE
DIGTAL
DIRECT
PROCESSING
CONTROL
DPC
MODE
PROGRAMMABLE
1
Hold down BACKGROUND.
2
Press both the corresponding button of the
component you're going to use (see the table
below) and one of the following buttons at the
same time; VISUAL POWER, TV/VIDEO, CH/
PRESET +/–, ANT TV/VTR, D.SKIP, (, 9, p,
0/), =/+, P, r.
Example: To start recording on a tape deck
while listening to a CD
While holding down BACKGROUND,
press 4 (or 5) and press r + ( at the
same time.
The following buttons correspond to the
components.
The button
Corresponds to
1
CD player
2
DAT deck
3
MD deck
4
Tape deck A
5
Tape deck B
6
LD player
7
VCR (remote control mode VTR 1
8
VCR (remote control mode VTR 2
9
VCR (remote control mode VTR 3
>10
DBS tuner
ENTER
DVD player
*
Sony VCRs are operated with a VTR 1, 2 or 3 setting
that corresponds to Beta, 8mm, and VHS,
respectively.
SYSTEM OFF
VISUAL
POWER
LD
TV
CD
TUNER
PHONO
5.1
INPUT
2
3
TV/VIDEO
5
6
Numeric and
D.TUNING
DISC
8
9
+
ENTER buttons
CH/
ENTER
PRESET
0
–
RMS/START
ANT
SWAP
TV/VTR
+
D. SKIP
P IN P
JUMP
p
P
r
TEST
TONE
— LEVEL —
+
+
REAR
CENTER
–
–
MASTER
BASS
VOL
BOOST
MUTING
*
)
*
)
*
)
Advanced Remote Operations
Changing the Factory Setting
of a FUNCTION Button
If the factory settings of the FUNCTION buttons (page
13) don't match your system components, you can
change them. For example, if you connect a Sony LD
player to the VIDEO 2 jacks, you can assign the VIDEO
2 button to set the remote to control the LD player.
Note that the settings of the TUNER and PHONO
buttons cannot be changed.
SLEEP
LEARN
SYSTEM CONTROL / FUNCTION
VIDEO 1
VIDEO 2
VIDEO 3
(AUTO CATEGORIZE SYSTEM)
TAPE
DAT/MD
CD
TV
CONTROL
1
2
ON
4
5
Numeric
7
8
and ENTER
BACK
GROUND
SHIFT
0
>
10
buttons
–
+
SUB CH
POSITION
0
)
=
— RMS —
DIRECTION
CLEAR
9
(
p
— SOUND FIELD —
ON/OFF
GENRE
MODE
EQ/
TONE
BAND
SLOPE
DIGTAL
DIRECT
PROCESSING
CONTROL
DPC
MODE
PROGRAMMABLE
1
Hold down the SYSTEM CONTROL/FUNCTION
button whose function you want to change
(VIDEO 2, for example).
2
Press the corresponding numeric button of the
component you want to assign to the SYSTEM
CONTROL/FUNCTION button (6 - LD player,
for example).
For the numeric buttons, see the table in
"Operating One Component While Using
Another" on this page.
Now you can use the VIDEO 2 button to control
your Sony LD player.
To reset the setting to the factory setting
Repeat the above procedure.
Getting Started
SYSTEM OFF
VISUAL
POWER
SYSTEM
LD
TV
TUNER
PHONO
CONTROL/
5.1
INPUT
3
FUNCTION
TV/VIDEO
6
D.TUNING
DISC
9
+
CH/
ENTER
PRESET
–
RMS/START
ANT
SWAP
TV/VTR
+
D. SKIP
P IN P
JUMP
P
r
TEST
TONE
— LEVEL —
+
+
REAR
CENTER
–
–
MASTER
BASS
VOL
BOOST
MUTING
29