Related Manuals for Clarke CROS3
Summary of Contents for Clarke CROS3
- Page 1 RANDOM ORBITAL SANDER MODEL NO: CROS3 PART NO: 6462012 OPERATION & MAINTENANCE INSTRUCTIONS LS1215...
-
Page 2: Specification
INTRODUCTION Thank you for purchasing this CLARKE Sander, which is designed for DIY and light workshop use only. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Safety Precautions
SAFETY PRECAUTIONS WARNING: READ ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/ OR SERIOUS INJURY. THE TERM “POWER TOOL” IN ALL WARNINGS LISTED BELOW REFERS TO YOUR RANDOM ORBITAL SANDER. 1) WORK AREA SAFETY a. - Page 4 c. Prevent unintentional starting. Ensure the trigger is in the off-position before connecting to power source, picking up or carrying the tool. Carrying power tools with your finger on the trigger or energising power tools that have the switch on invites accidents. d.
- Page 5 SAFETY INSTRUCTIONS FOR KICKBACK WARNING: KICKBACK IS A SUDDEN REACTION TO A PINCHED OR SNAGGED ROTATING WHEEL, BACKING PAD, BRUSH OR ANY OTHER ACCESSORY. PINCHING OR SNAGGING CAUSES RAPID STALLING OF THE ROTATING ACCESSORY WHICH IN TURN CAUSES THE UNCONTROLLED POWER TOOL TO BE FORCED IN THE DIRECTION OPPOSITE OF THE ACCESSORY'S ROTATION AT THE POINT OF THE BINDING.
-
Page 6: Safety Symbols
SAFETY SYMBOLS Read instruction Wear dust mask manual before use Class 2 Double Wear ear defenders Insulated CE Mark Wear safety glasses Weee Directive DUST EXTRACTION The sander is provided with a dust extraction facility. Please note however, that this does not preclude the user from wearing a face mask to prevent the inhalation of dust particles. -
Page 7: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. Connecting it to any other power source may cause damage. -
Page 8: Product Overview
PRODUCT OVERVIEW DESCRIPTION DESCRIPTION Handle Auxiliary Handle Speed Control Lock-On Button Trigger Dust Bag Sanding Pad 2 x 60G sanding discs (not shown) 2 x 100G sanding discs (not shown) 1 x 150G sanding disc (not shown) Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 9: Preparation And Use
PREPARATION AND USE FITTING A SANDING DISC 1. Select the disc to be used. • This MUST be the correct 125mm diameter disc with hook and loop backing. 2. Ensure the sander is switched off and the plug is removed from the socket. -
Page 10: Operation
OPERATION 1. Plug into the mains socket and switch on, 2. Place the sanding disc on the workpiece. • Hold the sander firmly with both hands. 3. Squeeze the trigger. • Work gently across the workpiece until smooth. 4. Release the trigger. •... -
Page 11: Maintenance
MAINTENANCE • Always inspect the sander before use and ensure it is in top condition. • Ensure all air vents are clear. (Use vacuum cleaner to clean the machine where possible). • Check the power cable to ensure it is sound and free from cracks, bare wires etc. -
Page 12: Troubleshooting
Wipe the exterior with a dry cloth. Excessive Worn brushes. This problem is easily remedied but Sparking. you should consult your CLARKE dealer for parts and advice. Sander does Check to ensure the fuse If the fuse is sound or blows not operate in the plug is sound. -
Page 13: Parts Diagram
PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Parts List
PARTS LIST DESCRIPTION DESCRIPTION Screw Bearing Partial Cover Of Left Housing Dust Collection Circle Left Housing Self-tapping Screw Spring Washer Handle Adjument Knob Sanding Paper Adjustable Handle Foam Sanding Pad Hex Bolt Self-tapping Screw Spring Washer Right Housing Washer Partial Cover Of Right Housing Bearing Cover Self Tapping Screw Bearing... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CROS3 and is the answer not in the manual?
Questions and answers