Index - Gardner Denver Electra-Screw EDEQHF Operating And Service Manual

INDEX
NOTE: Numbers preceding dash are Section Numbers -- Numbers following dash are Page Numbers
Addition of Oil Between Changes ...............................5-2
Air Control Components .............................................4-2
Air Cooled Unit installation ..........................................2.l
Air Filter Element, Heavy Duty ....................................6-1
Air Filter Element, Standard Duty ................................6-2
Air Filter Element Life, Heavy Duty ..............................6-l
Air Filter Element Life, Standard Duty .........................6-2
Air Filter Element Servicing Instructions ............. 6-1, 6-2
AIR FILTER (SECTION 6) .. . .......................................6-1
Air Flow in the Compressor System ...........................l-l
Air Receiver, Auxiliay ..................................................2.3
AUTO-LAG Button with LED ........................................4-3
AUTO-LEAD Button with LED .....................................4-3
Auto Sentry S -Auto Lag Button .................................4-3
Auto Sentry S -Auto Lead Button ...............................4-3
Auto Sentry S - Constant Run Button .........................4-3
Auto Sentry S - Control Pad Diagram .........................4-8
Auto Sentry S - Controller with Keypad ......................4-3
Auto Sentry S - Emergency Stop Pushbutton ............4-3
Auto Sentry S - Hourmeter ..........................................4.3
Auto Sentry S - Lead-Lag operation ...........................4-6
Auto Sentry S - Programming and Set-Up
instructions ..........................................................4.4
Auto Sentry S - Stop/Reset Button .............................4-3
Auxiliay Air Receiver ...................................................2.3
Basic information .........................................................l.l
BELT DRIVE (SECTION 7) ..........................................7-1
Belt Tension, ChecMng ................................................7.l
Blowdown Valve ..........................................................4.2
Blowdown Valve Piping ...............................................2.4
CHANGE AIR FILTER LED ..........................................4-4
CHANGE SEPARATOR LED ........ ...............................4-4
Check, Daily .................................................................3.2
Check, Pre-Start-Up ....................................................3.l
Cold Ambient Operation ..............................................5-2
Cold Weather Operation ..............................................2.2
Compression Principal ................................................l.l
Compressor Oil Cooler ................................................5.5
Compressor Oil Filter ..................................................5.4
Compressor Oil System ..............................................5-1
Compressor System, Air Flow ....................................l-l
CONSTANT RUN Button with LED .............................4-3
Control Piping ..............................................................2.3
CONTROLS AND INSTRUMENTS (SECTION 4) .......4-1
Control System Operation ...........................................4.3
AUTO LAG Button with LED ................................4-3
13-8-610
AUTO LEAD Button with LED .............................4-3
CHANGE AIR FILTER LED ..................................4-4
CHANGE SEPARATOR LED ...............................4-4
CONSTANT RUN Button with LED .....................4-3
HIGH AIR TEMPERATURE LED .........................4-3
MOTOR OVERLOAD LED ...................................4-4
Pressure and Temperature Digital Readouts .....4-4
STOP/RESET Button with LED ...........................4-3
Cooler, Compressor Oil ..............................................5.5
Cooling, Lubrication and Sealing ...............................1-1
Daily Check ..................................................................3-2
Decals ...................................................................l.7. 1-8
Definitions of Error Messages .....................................4.4
Discharge Service tine ...............................................2.3
Drain, Oil Resewoir .....................................................2.2
Draining and Cleaning The Oil System ......................5-3
Electrical Wiring ...........................................................2.4
Element, Air Filter .................................................6.l. 6-2
Emergency Stop Pushbutton .....................................4-3
Enclosure ....................................................................2.2
Error Messages - Definitions .......................................4.4
Extreme Cold Weather Operation, Installation ...........2-3
Filling Oil Reservoir ....................................................5.3
Filter, Nr ................................................................6.l. 6-2
Filter, Compressor Oil .................................................5.4
Filter Element ........................................................6.l. 6-2
Filter Element tife .................................................6.l. 6-2
Foundation .................................................................2.l
Gauge, Oil Sight ...................................................4.2. 5-3
GENERAL INFORMATION (SECTION 1) ..................1-1
Grease Recommendations, Electric Motor ................2-4
Grounding ....................................................................2.4
Heavy Duty Air Filter....................................................6.l
HIGH AIR TEMPERATURE LED ..................................4-3
High Discharge Temperature Shutdown ....................4-l
High Temperature Operation .....................................5-1
Hourmeter ....................................................................4.3
Inlet Line ....................................................................2.3
Inlet Line Lengths ........................................................2.3
Inlet Tube, Air Filter .....................................................6.l
Inlet Valve ...................................................................4.2
INSTALLATION (SECTION 2) ....................................2-1
Page ii