Download Print this page

GE RAB24 Installation Instructions Manual

Standard steel wall sleeve for 24” thru-the-wall air conditioners
Hide thumbs

Advertisement

Quick Links

Before you begin - Read these instructions completely
and carefully. IMPORTANT – OBSERVE ALL
GOVERNING CODES AND ORDINANCES. Note to
Installer – Be sure to leave these instructions with the
Consumer. Note to Consumer – Keep these instructions
with your Owner's Manual for future reference.
NOTE: Handle the wall sleeve carefully.
CRITICAL DIMENSIONS
Outside wall
"C"
NOTE: Care should be taken in location of electrical
supply entry in relationship to wall sleeve to ensure
access to power once the unit is installed.
Ceiling
"A"
"B"
Roomside
"D"
Installation Instructions
for your new
RAB24
Standard Steel Wall Sleeve
for 24" Thru-The-Wall Air
Conditioners
WALL SLEEVE LOCATION
be located in an outside wall to ensure proper
distribution of conditioned air. It should be located
in a portion of the wall where there is no electrical
obstructions immediately inside or outside.
Dimensions Recommended Installation Clearance
A
min.
B
C
min.
D
E
INSTALL WALL SLEEVE LEVEL FROM SIDE TO SIDE
AND WITH A SLIGHT TILT FROM FRONT TO REAR
Top of wall sleeve
Top of case
"E"
31-5000413 Rev. 1 07-19 GEA
Outside wall
"E"

Advertisement

loading

  Related Manuals for GE RAB24

  Summary of Contents for GE RAB24

  • Page 1 Installation Instructions for your new RAB24 Standard Steel Wall Sleeve for 24” Thru-The-Wall Air Before you begin - Read these instructions completely and carefully. IMPORTANT – OBSERVE ALL Conditioners GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer.
  • Page 2: Step 1: Preparation Of The Wall

    Installation Instructions STEP 1: Preparation of the wall STEP 2: Assemble Wall Sleeve and lintels should be used to support the block above the wall sleeve. The wall sleeve will not support the con- Front View and width: panel until all tabs lock completely. Front View Header - 4”...
  • Page 3 Installation Instructions STEP 3: Installation of the wall sleeve in STEP 3: Installation of the wall sleeve in the wall opening the wall opening (cont.) OPTION 1 OPTION 2 Installation of the wall sleeve into wall using 1. Position the wall sleeve into the wall. Refer to chart on mounting brackets IMPORTANT: Install wall sleeve level from side to side and with a slight...
  • Page 4 1. The wall sleeve should not be installed in a thick wall where “tandem” type “perpendicular” type Outdoor grille NOTE: Wall Case Sleeve Flashing Caulk* Drain Kit (optional) Drip rail *NOTE: It is critical to caulk around perimeter of wall sleeve RAD10 External Drain the kit. A Quality Product of GE Appliances...
  • Page 5 Instructions d’installation pour votre nouveau RAB24 Gaine d’acier standard pour climatiseurs 24 po à travers mur Avant de commencer - Veuillez lire ces instructions attentivement et en totalité. IMPORTANT – OBSERVEZ TOUS LES CODES ET RÈGLEMENTS EN VIGUEUR. Note à l’installateur – Assurez-vous de laisser ces instructions au consommateur.
  • Page 6: Étape 1: Préparation Du Mur

    ÉTAPE 1: Préparation du mur ÉTAPE 2 : Préparation de la gaine pour RAB24 seulement Il faut installer la gaine murale pendant la construction et utilis- er des linteaux pour supporter les blocs au-dessus de la gaine Assemblage de la gaine murale murale.
  • Page 7 Instructions d’installation ÉTAPE 3: Installation de la gaine dans ÉTAPE 3: Installation de la gaine dans l’ouverture murale l’ouverture murale (suite) OPTION 1 OPTION 2 Installation de la gaine dans le mur à l’aide de sup- 1. Placez la gaine dans le mur. Reportez-vous au tableau de ports de montage la page 1 pour la saillie côté...
  • Page 8 Pour l’installer, reportez-vous au manuel d’instructions Gouttière Drip rail inclus dans la trousse. REMARQUE: **Il est essentiel de calfeutrer les périmètres du solin et de la gouttière là où ils joignent le bâtiment et Un produit de qualité GE Appliances...