Related Manuals for Faber Camino Pro CAPR36SS600
Summary of Contents for Faber Camino Pro CAPR36SS600
- Page 1 CAMINO PRO Installation Instructions Use and Care Information Instructions d'installation Utilisez et d'entretien Instrucciones de instalación Información de uso y cuidado CAPR36SS600 CAPR36SS1200 CAPR48SS1200...
- Page 2 READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium setting. Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
-
Page 3: Venting Requirements
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. Ducted fans must always be vented to the outdoors. ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED. This rangehood requires at least 24" of clearance between the bottom of the rangehood and the cooking surface or countertop. - Page 4 WARNING • Electrical ground is required on this rangehood. • If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO NOT use for grounding. • DO NOT ground to a gas pipe. • DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or grounding circuit could result in electrical shock.
- Page 5 1 MOTOR - RANGEHOOD DIMENSIONS 36" 1 MOTOR RANGEHOOD REAR VENTING...
- Page 6 2 MOTOR - RANGEHOOD DIMENSIONS 36" 10" DUCT TRANSITION FOR 2 MOTOR RANGEHOOD 36" 9 13/16”...
- Page 7 2 MOTOR - RANGEHOOD DIMENSIONS 48" 10" DUCT TRANSITION FOR 2 MOTOR RANGEHOOD 48" 9 13/16”...
- Page 8 MAIN PARTS 1 MOTOR RANGEHOOD 36" Components Ref. Qty. Product Components Hood Body, complete with: Controls, Light Filter knobs Grease rail Recirculation Vent Grill Damper ø 5 7/8" Blower Ref. Qty. Installation Components Wall plug Screws 3/16"x1 15/16" Screws 1/8"x 3/8" Qty.
- Page 9 MAIN PARTS 2 MOTOR RANGEHOOD 48" Components Ref. Qty. Product Components Hood Body, complete with: Controls, Light Duct transition Filter knobs Grease rail Recirculation Vent Grill Damper ø 5 7/8" Blower Ref. Qty. Installation Components 12a 2 Wall plug 12b 4 Screws 3/16"x1 15/16"...
-
Page 10: Parts Needed
PARTS NEEDED 6" Round Metal Ductwork AVAILABLE ACCESSORIES Telescopic Chimney Duct Cover: - sku#: CHIM3448 (Use with 48" Camino Pro) - sku#: CHIM2224 (Use with 36" Camino Pro) - sku#: CHIM2248 (Use with 36" Camino Pro) - sku#: CHIM3424 (Use with 48" Camino Pro) CFM Reducer Accessory Kit sku#: CFMRED CFM Reducer Accessory Kit sku#: CFMRED-2 Activated Charcoal Filter sku #: FILTER1... - Page 11 1 MOTOR RANGEHOOD REAR INFORMATION 6" Rear 1 MOTOR RANGEHOOD REAR DUCTED INSTALLATION For a rear ducting installation the blower bracket needs to be screws as shown. Once the screws are removed, 180° extract it from the body of the Hood and position it so the transition opening is facing to the rear wall (from the back remove and rotate...
- Page 12 Put the motor in the hood body. Install the motor into the upper of the hood using the 2 screws 12e supplied. Connect the wire cable 9 hole end to the motor. 9 hole end...
- Page 13 1 MOTOR RANGEHOOD TOP DUCTED INSTALLATION Put the motor in the hood body. Install the motor into the rear of the hood using the 2 screws 12e supplied. Connect the wire cable 9 hole end to the motor. 9 hole end...
- Page 14 2 MOTOR RANGEHOOD TOP DUCTED INSTALLATION FIGURE 16 Put the 2 motors in the hood body. Inside the hood there is a blower bracket divider and the motors will be one a side. Install the 2 motors into the sides of the blower bracket using the 4 screws 12e supplied. 9 hole end 9 hole end 9 hole end...
-
Page 15: Installation Instructions
INSTALLATION INSTRUCTIONS Install Damper that is included with the Hood before connecting to the ductwork. One for 1 motor model. Two for 2 motor model. Installation Instruction for Mounting on the Wall Min. 24" Min. 30" Draw a vertical line on the supporting wall as high as practical, at the center of the area in which the hood will be installed. - Page 16 Installation for 1 Motor Rangehood L = 19 11/16” Ø 1/2” 36” Mark the wall where indicated, 16 " above the horizontal line and at L distance on the left and right of vertical line. The distance L changes for all dimension of Hood. For a different type of Wall, it's possible to use only the bracket by remove the plug and the screw from...
- Page 17 Installation for 2 Motor Rangehood Ø 1/2” L = 19 11/16” - 1/8” 36” - 48” Mark the wall where indicated, 16 " above the horizontal line and at L distance on the left and right of vertical line. The distance L changes for all dimension of Hood. For a different type of Wall, it's possible to use only the bracket by remove the plug and the screw from...
- Page 18 Hook the hood body onto the wall plugs 12a. Use a level to insure that Fixing Bracket is level by adjusting the screws as shown in the picture. Mark the wall where indicated. Drill directly into ø 5/16" holes at all the center points marked. Ø...
- Page 19 1 AND 2 MOTORS STANDARD DUCTING METHODS Vertical Horizontal Rear motor range- hood only) 1 AND 2 MOTORS DUCTING METHODS 6" Install Roof or Wall Cap purchased separately. Connect the 6" metal ductwork to the Roof or Wall Cap and then attach ductwork.
- Page 20 2 MOTORS DUCTING METHODS 10" Fix the Duct transition in the hood body with 4 screws 12d. Install Roof or Wall Cap purchased separately. Connect the 10" metal ductwork to the Roof or Wall Cap and then attach ductwork.
- Page 21 Non Ducted - Recirculation Option For Non-Ducted Recirculation venting route the ductwork to a location above the hood where the discharge is vented back into the room. Use the included Recirculation Vent Grill (9) to cover the opening. Secure the grill with the 2 screws (12f) provided in the Install Kit.
- Page 22 RECIRCULATION INSTRUCTIONS open space upper upper cabinet cabinet rangehood rangehood cooking surface cooking surface Note: recommended for 600 CFM version only Note: It is recommended that pro- fessional style cooking always be vented to the outside; for recirculat- ing installations, some duct work is required to exhaust the unit out of the cabinet.
- Page 23 Hook the Grease rail (8) positioning it inside the hood. It is possible to wash and reposition the rail inside the hood. Installation of wiring connection Switch off the dedicated power supply to the hood. Remove the wiring electrical knockout using a Cable through the electrical knockout.
- Page 24 The 36" hood has 3 Filters. The 48" hood has 4 Filters. INSTALLATION CONTINUED Optional Telescopic Chimney Extension Installation Refer to Instructions inthe Chimney Duct Ccover Accessories.
- Page 25 USE AND CARE INFORMATION Rangehood Control Panel The control panel is located in the center of the hood bottom. Function Operation LED Color / Light Pattern Lights - Dimmer Lights - High Lights - Off Speed 1 Green - Solid Speed 2 Yellow - Solid Speed 3...
-
Page 26: Lighting Unit
solution or washed in the dishwasher. They should be cleaned every 2 months, or more frequently if use is particularly heavy. • Install the grease rail into the back of the hood, into • the rangehood. • with the knobs facing out into the spring loaded slot. in the back of the hood. -
Page 27: Wiring Diagram
Wiring Diagram... - Page 28 To obtain warranty service, contact the dealer from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber distributor, contact us at (508) 358-5353 for the name of a distributor in your area.
Need help?
Do you have a question about the Camino Pro CAPR36SS600 and is the answer not in the manual?
Questions and answers