Installing The Projector And A Screen - Sony VPL-HS3 Operating Instructions Manual

Installing the Projector and
a Screen
The installation distance between the projector and
screen varies depending on the size of the screen.
Note
When installing the projector and screen, be sure not to tilt them.
If you tilt either or both of them, the adjustment cannot be
correctly carried out.
1
Determine the installation
position of the projector and
screen.
Screen
d
a
a: Minimum projection distance between the
screen and the center of the projector's lens
when you place the projector on the side
("Side Shot"), or when you place the
projector with the center of the screen and the
center of the lens aligned.
b: Maximum projection distance between the
screen and the center of the projector's lens
when you place the projector on the side, or
when you place the projector with the center
of the screen and the center of the lens
aligned.
c: Maximum horizontal distance between the
right/left end of the screen and the center of
the projector's lens when the projector is
placed on the side (when you use projection
distance a)
d: Maximum horizontal distance between the
right/left end of the screen and the center of
the lens when the projector is placed on the
side (when you use projection distance b)
8
Step 1: Installing the Projector
GB
f
8˚ e
5˚
b
Projector
e: Maximum vertical distance from the bottom
of the screen to the center of the projector's
lens when you place the projector on the side
(when you use projection distance a)
f: Maximum vertical distance from the bottom
of the screen to the center of the projector's
lens when you place the projector on the side
(when you use projection distance b)
When projecting using "Side Shot"
adjustment only (1 page 17)
Position the projector with the lens end within
the area in the illustration, by using the
values a, b, c and d in the table below as a guide.
Screen
size 40 60
(inches)
1.1 1.7
a
(3.6) (5.6) (7.2)
1.2 1.8
b
(3.9) (5.9) (7.9)
-0.2 -0.2 -0.3
c
(-0.7) (-0.7) (-1)
0 0
d
(0) (0)
Tip
The table shows the distances when projecting the video
signals. Distances used for projecting a 1080i/720p format
signal and computer's signal are shown on page 40 .
Note
If you project the picture using "Side Shot" only, set "V
Keystone" in the INSTALL SETTING menu to "Manual,"
and adjust the level to "0."
When projecting using both "Side Shot"
and "V Keystone" adjustments (1 page
18)
Position the projector with the lens end within
the area in the illustration, by using the
values a to f in the table below as a guide.
Screen
size 40 60
(inches)
1.2 1.7
a
(3.9) (5.6) (7.2)
1.3 1.9
b
(4.3) (6.2) (8.2)
-0.2 –0.3 –0.4
c
(-0.7) (–1) (–1.3)
Unit: m (feet)
80 100 120 150
2.2 2.8 3.3 4.2
(9.2) (10.8) (13.8)
2.4 3 3.6 4.5
(9.8) (11.8) (14.8)
-0.4 -0.4 -0.4
(-1.3) (-1.3) (-1.3)
0 0 0 0
(0) (0) (0) (0)
Unit: m (feet)
80 100 120 150
2.2 2.8 3.4 4.2
(9.2) (11.2) (13.8)
2.5 3.1 3.7 4.6
(10.2) (12.1) (15.1)
–0.6 –0.7 –0.9
(–2) (–2.3) (–3)