Crestron FlipTop FT2 Series Quick Start page 2

3. Slide the attached keystone plate module down into the same
module slot using the front and rear guide ribs to assist with
positioning.
Install the Locking Bars
1. Place the locking bars into position so that the screws attached to
the locking bars engage the screw holes in the FlipTop assembly.
2. Using a manual torque screwdriver set to its lowest possible
setting, hand tighten the locking bar screws until the locking bars
are secured to the FlipTop assembly.
CAUTION: Do not overtighten the locking bar screws.
Position of Locking Bars
Locking bars (3)
FT2A modules
FlipTop
assembly
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All
other languages are a translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with
specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Install the Bezel
Place the bezel onto the FlipTop assembly so that the retractable lids fit
inside the bezel openings. The bezel is held in place using magnets.
Position of Bezel
Bezel opening
for retractable lid
Lid retraction
button
Retractable lid
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Operate the FlipTop Assembly
To operate the FlipTop assembly:
1. Tap the lid retraction button to retract the one-touch lid, which
disappears into the assembly.
2. Pull out a cable and lay it on the tabletop.
3. Lift the cable vertically above the FlipTop assembly to retract the
cable gently back into the assembly.
4. Close the lid by lifting it vertically and returning it over the FlipTop
assembly.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks of
Additional Information
Scan or click the QR code for detailed product information on the
Crestron website.
FT2-700-MECH
Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either a
trademark or registered trademark of the HDBaseT Alliance in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI
Licensing LLC in the United States and/or other countries. The UR logo is either a trademark
or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products.
Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc. Quick Start - Doc. 8216F
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576 Specifications subject to
www.crestron.com change without notice.
(2053627)
05.19