Sherman Workshop MIG 200M User Manual

Sherman Workshop MIG 200M User Manual

Semi-automatic welding inverters

Advertisement

19.04.01 v3.10
USER MANUAL
SEMI-AUTOMATIC WELDING inverters
MIG 200M

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MIG 200M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sherman Workshop MIG 200M

  • Page 1 19.04.01 v3.10 USER MANUAL SEMI-AUTOMATIC WELDING inverters MIG 200M...
  • Page 2 WARNING! Before installing and commissioning, please read these instructions 1. GENERAL Commissioning and operation of the device can be made only after a careful reading of this handbook. Due to the continuous development of technical equipment, some of its functions can be modified and operation may differ in detail from the description in the manual.
  • Page 3 Poisoning prevention vapors and gases evolved at the time of welding of coatings for welding electrodes and evaporation of metals: • Use ventilation and exhaust installed in limited air exchange. • Blow fresh air when working in a confined space (tanks) •...
  • Page 4: Specifications

    3. GENERAL DESCRIPTION Semi-automatic MIG welder 200M is used for manual welding of steel and non-ferrous metals MMA (covered electrode) and MIG / MAG gas-shielded self-shielded wire or without shielding gas. It can also be used to braze thin (3mm) galvanized sheets. It can be used indoors or covered, if directly exposed to weathering.
  • Page 5: Connection To The Mains

    Duty cycle Duty cycle is based on a period of 10 minutes. Duty cycle of 60% means that after 6 minutes of operation of the device is required for 4-minute break. Duty cycle of 100% means that the machine can operate continuously without interruption. Attention! Heating test was carried out in the ambient air temperature.
  • Page 6 WIRE FEED SpOO L MIG / MMA INVERTER MMA PROCESS TORCH MIG / L SpOO GUN MIG 200M TECWELD Pi r ot Pol ak Sherman 41- 943 s Piekary Sl. Ul. Szmar agdowa 21 / 3/6 Ty pe: MIG 200M...
  • Page 7 9. Socket negative polarity. 15. The display of the welding current 10. The seat MIG. 16. The power switch. 11. Socket positive polarization. 17. The gas connection. 12. The control plug holder Spool Gun. 18. fan 13. The connector polarity switch (for MIG). 19.
  • Page 8 8.1.3 arc Initiation 1. Touch electrode to the workpiece, and short rub tear. 2. In the event of initiation of the arc electrodes, wherein the sheath when solidified, creates a non-conductive slag, the pre-clean the tip of the electrode by repeatedly impact against a hard surface until the metal in contact with the work piece. 8.2 MIG / MAG AND braze 8.2.1 Preparing for operation 8.2.1.1 Welding and brazing gas-shielded...
  • Page 9 8.2.2 Setting the welding parameters and braze 1. Turn on the power supply connector on the rear of the device. 2. The switch method of welding (5) to position MIG / MAG welding. 3. The rotary knob (7) to the appropriate welding voltage. 4.
  • Page 10: Maintenance Instructions

    Starting in these conditions, cold welding can cause damage. It is recommended that in the event of welding operation outdoor place it under a roof to protect against adverse weather conditions. MIG 200M should be operated under the following conditions: changes in the effective value of the supply voltage is not greater than 10% ambient temperature of from -10 °...
  • Page 11: Wiring Diagram

    12 WIRING DIAGRAM...
  • Page 12 13. INSTRUCTION STORAGE AND TRANSPORT The device should be stored at -10 ° C to + 40 ° C and relative humidity 80% free of corrosive fumes and dusts. Transportation of packaged devices should be covered means of transport. For transport the packaged unit must be secured against slipping and ensure the correct position. 14.
  • Page 13: Declaration Of Conformity

    41-909 Bytom ul. Cross 3 Declare that the said product: semi-automatic welding machine Trade name: MIG 200M Type: MIG 200M Manufacturer's trademark: to which this declaration relates complies with the following directives of the European Union and national provisions implementing the Directive:...

Table of Contents

Save PDF