Trend Micro TippingPoint TPS 8200TX Installation Instructions Manual

Hide thumbs Also See for TippingPoint TPS 8200TX:

Advertisement

Install your TPS 8200TX and 8400TX
security devices
This information provides detailed installation instructions for your Threat Protection System (TPS)
8200TX and 8400TX security devices.
Before you begin
Before you begin, go to the TMC at https://tmc.tippingpoint.com, and see the documentation for your
product to:
— Review the product release notes for information about product updates.
— Review the detailed installation and safety documentation for your product.
Important:
The 8200TX and 8400TX security devices may require a license update to ensure
sufficient inspection throughput when you connect to your network. For more information, see
"Step 9. Install your license
— Make sure the power capacity for your installation meets the documented requirements:
• 8200TX device: AC Voltage 100 to 240; Current 12 to 6A; Frequency 47 to 63 Hz
• 8400TX device: AC Voltage 100 to 240; Current 12 to 6A; Frequency 47 to 63 Hz
• 8200TX and 8400TX devices: DC Voltage -40 to -60; Current 24 to 16A
Warning:
Before you turn on power for your product or connect to your network, ensure your
installation meets all power capacity, ventilation, and other safety guidelines. To avoid injury and
damage, you should always review and adhere to all guidelines described in the safety, specification, and
installation documentation. For more information, see the Read Me First document that was included in
your product shipment.
Publication Part Number DOCMT-1001
Edition: August 2017, Rev A1
package," on page 7.
*DOCMT-1001*
DOCMT-1001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TippingPoint TPS 8200TX and is the answer not in the manual?

Questions and answers

Summary of Contents for Trend Micro TippingPoint TPS 8200TX

  • Page 1 Install your TPS 8200TX and 8400TX security devices This information provides detailed installation instructions for your Threat Protection System (TPS) 8200TX and 8400TX security devices. Before you begin Before you begin, go to the TMC at https://tmc.tippingpoint.com, and see the documentation for your product to: —...
  • Page 2 Refer to the following diagram of the chassis front panel when you install and configure the device. Figure 1. TippingPoint TPS 8200TX and 8400TX security devices – front panel 1. I/O modules 5. Stack LED 9.
  • Page 3: Step 3. Connect The Power Supply

    Step 2. Attach the device to the rack Unpack the rail kit that shipped with your security appliance and review the installation documentation on the TMC. Note: The TPS 8200TX and 8400TX devices have the following weight values: — 8200TX devices: 32 pounds (14.5 kilograms) —...
  • Page 4 To remove the blank module, slide the slide latch ( ) to the right and pull on the grab point ( Figure 2. TippingPoint TPS 8200TX and 8400TX security devices – blank module Install your TPS 8200TX and 8400TX security devices...
  • Page 5: Step 5. Attach The Cables

    To insert an I/O module, slide the module into the empty module slot. When the module is in the correct position, the slide latch automatically slides into position. Important: When you insert a bypass I/O module, the bypass I/O module always starts up in bypass mode.
  • Page 6: Step 7. Check Led Indicators

    Step 7. Check LED indicators When you turn on the device, the system completes a series of component checks and then displays LED indicators to show the status of each component: — Stack Master status • Solid green: Indicates that the device is the stack master. —...
  • Page 7 Verify your product license provides sufficient inspection throughput. By default, an 8200TX or 8400TX security device is unlicensed and provides reduced inspection throughput for testing and evaluation purposes only. Table 1: TippingPoint TPS 8200TX and 8400TX security devices – unlicensed inspection throughput Security device Unlicensed inspection throughput...
  • Page 8: Where To Go Next

    When you complete initial setup, you can configure network interface types appropriate to the surrounding network by using the ports you connected. See “Where to go next,” on page 8. Where to go next After you attach network connections, network traffic passes through the device using the default filter configuration.
  • Page 9 This document contains confidential information, trade secrets or both, which are the property of Trend Micro. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from Trend Micro or one of its subsidiaries.

This manual is also suitable for:

Tippingpoint tps 8400tx

Table of Contents