Graphic Equalizer; Quick Start - Rane DEQ 60L Manual

CUT +
0 6
• 5
1 4
• 3
2 2
• 1
A
3 0
• 1
4 2
• 3
5 4
• 5
6 6
25 31.5 40 50 63 80 100
CUT +
0 6
• 5
1 4
• 3
2 2
• 1
B
3 0
• 1
4 2
• 3
5 4
• 5
6 6

QUICK START

We know you know how to use an equalizer. Just read this sec-
tion for the unique things to be aware of in the DEQ 60L.
We know you know how to use a realtime analyzer, but using
PERFECT-Q mode will make that job a lot easier. Since there is
no interaction between filters, the multiple adjustments through
all the bands just to get the analyzer to read flat is a thing of the
past. One pass should do the trick. Then use the TONE controls
or CUT FILTERS for general sweetening. We know your sound
is important and your time is valuable.
If you want to compare the sound of your old (non-Rane) EQ
to this one, and you are used to the way the slider bands interact,
then use PROPORTIONAL-Q mode.
Activating the CUT-ONLY switch puts both equalizer chan-
nels in the high resolution CUT 0 to -12 dB (gray number scale).
To prevent unwanted sudden volume shifts when switched, the
outputs mute for a moment, then slowly increases in volume.
The A and B switches are like memories or control assigns.
Normal stereo use would set the top row A (Left), and the bot-
tom row to B (Right). But if you are running in stereo, and both
WEAR PARTS: This product contains no wear parts.
OPERATORS MANUAL
125 160 200 250 315 400 500 630 800 1.0k 1.25k 1.6k
+ CUT
12
10
8
6
4
2
0
2
4
6
8
10
12
2.0k 2.5k 3.15k 4.0k 5.0k 6.3k 8.0k 10k 12.5k 16k 20k
+ CUT
12
10
8
6
4
2
0
2
4
6
8
10
12
sides use the same EQ curve, you can set both switches to A.
Now the top EQ curve controls both left and right channels.
Switching these to B will use the bottom EQ curve for both
channels. This is great for switching EQ when a source changes.
Just be aware of where these switches are, an unassigned EQ row
will have no audible effect. These switches also affect the CUT
FILTERS, TONE CONTROLS, and LEVELS.
The channel BYPASS switches have two modes, set by the
rear panel switch. When set to FILTERS, the BYPASS switch
only bypasses the EQ, TONE and CUT FILTERS. The LEVEL
controls and other switches remain active. When set to ALL,
the BYPASS switches ignore everything including the LEVEL
controls.
You have several connector choices on the rear. However, use
only ONE type of INPUT on each channel. These Inputs do not
sum. But you may use any combination of OUTPUTS simulta-
neously if desired. Polarity convention on the XLR jacks is pin 2
positive, pin 3 negative and pin 1 shield (chassis ground).

GRAPHIC EQUALIZER

TONE CUT FILTERS LEVEL
+ +
0 6 240 5k 12 12
BYPASS
1
2
3 120 7k
EQ
4
5
6 0 60 10k 0 0
-12 -6
7
8
9 30 14k
10
11
∞
12 15 20k 12 12 DEQ 60L
+
GRAPHIC EQUALIZER
LOW MID HIGH LOW HIGH IN OUT
+ +
0 6 240 5k 12 12
BYPASS
1
2
3 120 7k
EQ
4
5
6 0 60 10k 0 0
-12 -6
7
8
9 30 14k
10
11
∞
12 15 20k 12 12
CUT-ONLY
+
DEQ 60L
A PERFECT-Q™ ±12
B PROPORT-Q ±6
IN
A
-3 0 +3 +6 +12 OL
OUT
A PERFECT-Q™ ±12
B PROPORT-Q ±6
IN
B
-3 0 +3 +6 +12 OL
OUT
POWER
Manual-1