Vermeiren. Thank you for your trust in the products of Vermeiren. To support you on the use of this wheelchair and its operating options, this manual is offered. Please read it carefully; it will help you to get familiar with the operation, capabilities and limitations of your wheelchair.
708D 2019-03 Product description Product description 1.1 Intended Use The wheelchair is intended for people with walking difficulties or no walking abilities. The wheelchair is designed to transport 1 person with a maximum weight of 120 kg. The wheelchair is suited for indoor and outdoor use.
708D 2019-03 Product description 1.5 Explanation of symbols CE conformity Maximum mass Type designation Indoor and outdoor use Maximum safe slope 1.6 Safety rules To prevent injury and/or damage to your wheelchair, make sure that no objects and/or body parts are caught in the spokes of the driving wheels.
708D 2019-03 Using your wheelchair Using your wheelchair This chapter describes the everyday use. These instructions are for the user and the specialist dealer. The wheelchair is delivered fully assembled by your specialist dealer. The instructions intended for the specialist dealer on how to set up the wheelchair are given in § 3.
708D 2019-03 Using your wheelchair 2.4 Mounting or removing the footrests Risk of injury CAUTION Check that the footrests are securely locked in place before use. Keep objects and people away from the footrests swing range. Mounting the footrests is done as follows: 1.
708D 2019-03 Using your wheelchair 2.6 Mounting or removing of armrests Risk of clamping - Keep fingers, buckles and clothes away from the CAUTION bottom side of the armrest. The armrests of the wheelchair can be mounted by following instructions.
708D 2019-03 Using your wheelchair 2.7 Transfer in and out the wheelchair Risk of injuries CAUTION In case you cannot perform the transfer in a safe manner, ask someone to assist you. Do not stand on the footplates.
708D 2019-03 Using your wheelchair 1. If available on the wheelchair, wear the safety belt. 2. Do not attempt to move on too high slopes. The maximum slope angles (upwards and downwards) are mentioned in §5. 3. Ask an attendant to help you on the slope.
708D 2019-03 Using your wheelchair Higher kerbs are negotiated backwards: 1. Turn the wheelchair to have the rear wheels facing the kerb. 2. Lean backwards and move your centre of gravity above the rear wheels. 3. Ask the attendant to pull the wheelchair on the kerb.
708D 2019-03 Using your wheelchair 2.13 Use of the wheelchair as seat in a motor vehicle WARNING The wheelchair has passed the crash of ISO 7176-19: 2008 and, as such, has been designed and tested for use only as forward-facing seat in a motor vehicle.
Page 15
708D 2019-03 Using your wheelchair Steps to secure the wheelchair user: 1. Remove both armrests. 2. If present, attach the wheelchair's pelvic belt. 3. Attach the occupant restraint belts according to the instructions of the strap-system manufacturer. 4. Wear the pelvic belt low across the front of the pelvis, so that the angle of the pelvic belt is within the preferred zone of 30°...
Installation and adjustment Installation and adjustment The instructions in this chapter are for the specialist dealer. To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility. WARNING Only use the settings described in this manual.
708D 2019-03 Installation and adjustment 3.4 Anatomical backrest (OPTIONAL) Risk of injury CAUTION Check that the backrest is secure before use. Avoid getting your fingers caught during the assembly process. To use the anatomical backrest, proceed as follows: 1. Unscrew the flexible backrest.
Risk of injuries and/or damage CAUTION Repairs and replacements may only be undertaken by trained persons, and only genuine replacement parts of Vermeiren should be used. Before each use Inspect the following points: All parts: Present and undamaged or unworn.
708D 2019-03 Maintenance 4.2.2 Cleaning Risk of damage CAUTION Never use a hose or high-pressure cleaner to clean the wheelchair. Wipe all rigid parts of the wheelchair with a damp cloth (not drenched). If necessary, use a mild soap, suitable for varnishes and synthetics.
The technical details below are only valid for this wheelchair, at standard settings and optimal ambient conditions. Take these details into account during use. The values are no longer applicable if your wheelchair has been modified, damaged, or is severely worn. Table 1: Technical specifications 708D Make Vermeiren...
Page 21
708D 2019-03 Technical specifications Handr im diameter 535 mm Horizontal location of axle (deflection) 21 mm Minimum turning radius 1619 mm Diameter PU Rear wheels 24" Tyre pressure, rear (driving) wheels Max. 3.5 bar Diameter PU steering wheels 200 mm Tyre pressure, steering wheels Max.
Page 23
Service registration form Service registration form This product (name): …………………………………….. was inspected (I), serviced (S), repaired (R) or disinfected (D): By (stamp): By (stamp): By (stamp): Kind of work: I / S / R / D Kind of work: I / S / R / D Kind of work: I / S / R / D Date: Date:...