Table of Contents
Related Manuals for Charnwood BD610
Summary of Contents for Charnwood BD610
- Page 1 BELT & DISC SANDER OWNERS MANUAL MODEL: BD610 Charnwood Machinery Ltd, Cedar Court, Walker Road, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
- Page 2 GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation.
- Page 3 BD610 Belt & Disc Sander Overview Sanding Belt Sanding Disc Sanding Belt Tension Lever Mitre Fence Tracking Adjuster Sanding Table Carry Handle Belt Angle Lock Table Angle Lock On/Off Switch Feet Specification 250mm (10”) Disc Diameter Disc Speed 2850rpm 150mm x 1220mm (6”...
- Page 4 Unpacking All items are contained in one carton. Carefully unpack and check that all the items are included as in the photograph. Assembly Place the sander on a level surface and adjust the two bed supporting bolts so that the belt is also level. Tighten the locknuts using a 13mm spanner.
- Page 5 Attaching the Work Table First, offer up the table so that the curved slots in the brackets align with the holes in the base, as shown. Insert one of the guide blocks into the upper slot and secure with two M5 x 16mm screws using a 4mm hex key.
- Page 6 From below the table, loosen the four bolts that connect the cast table to the brackets using a 10mm spanner. Adjust the table so there is a maximum gap of 1.6mm between its rear edge and the sanding disc. This will prevent fingers being trapped when using the sander.
- Page 7 The belt stop bracket is attached using the four socket head screws and washers provided. Attach the belt stop to the bracket. Adjust the Rest so that it is at 90 degrees to the belt and tighten the four mounting bolts.
- Page 8 It is essential to use dust extraction when using your sander. There is a single extraction port for the belt and disc with an inside/outside diameter of 45/50mm. A 50mm diameter hose will connect directly to the port. Our adaptor 100/58RC can be used to convert for using 100mm diameter hose.
-
Page 9: Using The Sander
Using the Sander This sander is designed for use with wood and wood-based products only. It should not be used for sanding metal and any such use would invalidate the warranty. The machine should be placed on a firm level surface before use. Sanding with the belt in the horizontal position The back stop must always be used as a... -
Page 10: Maintenance
Sanding with the Disc The disc sander is ideally suited to smoothing end grain and fine-tuning angled cuts with the aid of the mitre guide. Whenever possible use the front half of the exposed disc as this will hold the workpiece against the table. - Page 11 Carefully remove the existing self- adhesive sanding disc using a flat-bladed scraper. Remove any residue from the sanding plate using mineral/methylated spirit. Peel the backing from the new sanding disc and apply to the sanding plate. Ensure that it is positioned centrally on the plate, then press firmly into place.
- Page 12 Lift the belt bed to the vertical position and remove both dust cover and tray. The belt can now be removed. Locate the new belt over the two rollers. Ensure that the arrow on the inside of the belt corresponds to the direction marked on the machine.
-
Page 13: Troubleshooting
Your local refuse amenity will have a separate collection area for EEE goods Declaration of Conformity for CE Marking Charnwood Declare that Belt & Disc Sander, Model BD610 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EU And further conforms to the machinery example for which the EC type examination Certificate No. -
Page 14: Parts Drawing
Parts Drawing... -
Page 15: Parts List
Parts List Part No. Description Part No. Description Philips Screw M4 x 6 Philips Screw M4 x 8 Baseplate Philips Screw M5 x 8 Left Dial Cable & Plug Suction Connection Vee Belt A600 Screw M6 x 8 Cable Sheath Flat Key A5 x 15 Motor Assy Non-Metallic Insert Nuts M8... - Page 16 Allen Wrench (S = 4*120) Allen Wrench (S =3*60) Allen Wrench (S = 5*80) Updated March 2019 Charnwood Machinery Ltd, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU, England Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net...