Table of Contents
Related Manuals for Charnwood BD15
Summary of Contents for Charnwood BD15
- Page 1 BELT & DISC SANDER OWNERS MANUAL MODEL: BD15 Charnwood Machinery Ltd, Cedar Court, Walker Road, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. - Page 3 Overview of BD15 Belt & Disc Sander Belt Guard Sanding Belt Belt Tension Adjuster Belt Sander Work Table Sanding Disc Disc Sanding Table Belt Table Tilt Lock On/Off Switch Disc Table Tilt Lock Rubber Feet Mitre Fence BD15 Specification 125mm (5”) Disc Diameter 25mm x 762mm (1”...
- Page 4 Unpacking All items are packed in one cardboard carton. Carefully unpack and check that all items are included as in the photograph. Assembly Attach the dust guard using the three phillips head screws and small washers.
- Page 5 Fit the disc table by tilting at the angle shown and slide into place. Then lift up in the slots. Lock the table in place using the two locking knobs and washers. Using a set square ensure that the table is set at 90 degrees to the sanding disc.
- Page 6 Lock the table into position using the locking handle and washer. Tip: Hold the nut insert on the left in place to stop it falling out then use the ratchet on the locking handle to tighten. Using a set square ensure that the table is set at 90 degrees to the sanding belt.
- Page 7 Looking from the front: If the belt moves sideways towards the disc then turn the tracking knob anti-clockwise. (A quarter turn is normally enough) Continue adjustments until the belt remains central on the roller. If the belt moves sideways away from the disc then turn the tracking knob clockwise.
-
Page 8: Using The Sander
Using The Sander This sander is designed for use with wood and wood-based products only. It should not be used for sanding metal and any such use will invalidate the warranty. Dust extraction must be used at all times. Before use make sure your sander is bolted down securely using the two bolt holes. - Page 9 Move the workpiece backwards and forwards over the curved end of the belt. Never present the end of a workpiece to the curved edge as this can cause it to kick back. The disc sander is ideally suited to smoothing end grain and fine-tuning angled cuts with the aid of the mitre guide.
-
Page 10: Maintenance
Maintenance Replacing the Sanding Disc Always ensure the machine is disconnected from the power supply before any maintenance. Remove the two work table locking knobs and slide out the work table. Remove the dust extraction guard by taking out the three screws. Carefully remove the existing self- adhesive sanding disc with the aid of a flat blade scraper. - Page 11 Replacing the Belt Remove the locking knob and belt guard. Take off the side cover by removing the two screws. Take the tension off the belt. Press and hold the tension wheel in, then slide the belt off the side. Slide the belt off through the slot in the table.
-
Page 12: Troubleshooting
Your local refuse amenity will have a separate collection area for EEE goods Declaration of Conformity for CE Marking Charnwood Declare that Belt & Disc Sander, Model BD15 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EU And further conforms to the machinery example for which the EC type examination Certificate No. - Page 13 Charnwood BD15 Parts Drawing...
- Page 14 Charnwood DB15 Parts List Part No. Description Part No. Description Screw Foot Screw Base Cover Main Body Switch Plate Screw Motor End Plate Washer Capacitor 8uf 450Vac, 50mm x 40mm dia, M8 mount with spades Switch KJD20-2 Screw Motor body...
- Page 15 Updated April 2019 Charnwood Machinery Ltd, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU, England Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...