Table of Contents
Related Manuals for Charnwood BD48
Summary of Contents for Charnwood BD48
- Page 1 BELT & DISC SANDER OWNERS MANUAL MODEL: BD48 Charnwood Machinery Ltd, Cedar Court, Walker Road, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. -
Page 3: Specification
Overview of BD48 Belt & Disc Sander Sanding Belt Tracking Adjuster Sanding Belt Tension Lever Sanding Disc Sanding Belt Table Sanding Table Table Angle Lock Mitre Fence Belt Angle Lock Dust Extraction Unit On Off Switch Rubber Feet Table Angle Lock Specification 200mm (8”) - Page 4 Unpacking All items are contained in one cardboard box. Carefully unpack and check that all items are included as in the photograph. Assembly Attach the Disc Worktable using two locking handles and washers.
- Page 5 Ensure the gap between the disc and rear edge of the worktable is a maximum of 1.6mm in order to prevent finger trapping. Using a set square ensure that the table is at 90 degrees to the sanding disc and lock in position.
- Page 6 If necessary, adjust the red index pointer to align with the zero degree mark on the angle scale using a cross point screwdriver. Loosen the belt angle locking screw using a 5mm hex key and raise the belt bed into a vertical position.
- Page 7 Again, using a set square, adjust the Worktable to 90 degrees to the sanding belt and lock into position. Set the red index pointer to align with the zero degree mark on the angle scale. Thread the open end of the Dust Bag through the retaining clip and attach to the dust port.
- Page 8 The port is 64mm/57mm external/internal diameter. Setting Up Tracking the belt Ensure the machine is disconnected Slowly rotate the belt by hand by turning the sanding disc, ensuring that it is travelling in the direction of the arrow. Note if the belt is tending to slide off the bed and to which side.
-
Page 9: Using The Sander
Using The Sander This sander is designed for use with wood and wood-based products only. It should not be used for sanding metal and any such use would invalidate the warranty. Sanding with the belt in the horizontal position The worktable must always be used as a support when carrying out edge or face sanding in the horizontal position. - Page 10 Sanding with the belt in the vertical position Sometimes the sanding on the belt is more convenient with it positioned vertically – or any angle in between 0 & 90 degrees. To adjust, loosen the locking screw using a 5mm hex key. Position the belt bed as required and then re- tighten the screw.
-
Page 11: Maintenance
Maintenance Replacing the Sanding Disc Always ensure the machine is disconnected from the power supply before changing the sanding disc. Remove the disc worktable and then the disc cover which is secured with six screws. Carefully remove the existing self- adhesive sanding disc with the aid of a flat bladed scraper. - Page 12 Replacing the Sanding Belt Remove the belt worktable. Position the belt horizontally by loosening the hex head screw with a 5mm hex key. Loosen this screw Remove this screw Release the tension on the sanding belt by pulling out the tension lever. Slide off the dust collecting cover Loosen the two screws at the rear of the belt which hold the bottom tray.
-
Page 13: Troubleshooting
Your local refuse amenity will have a separate collection area for EEE goods Declaration of Conformity for CE Marking Charnwood Declare that Belt & Disc sander, Model BD48 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2014/30/EU And further conforms to the machinery example for which the EC type examination Certificate No. - Page 14 Charnwood BD48 Parts Drawing...
- Page 15 Charnwood BD48 Parts List Part No. Description Part No. Description Rubber Foot Philips Screw M4 x 10 Bottom Plate Philips Screw M8x5 Lock Washer D8 Flat Washer D8 Base Connect Tube Big Pulley Poly V Belt Bearing 6000RZ Spring Washer D26 Philips Screw ST4.2 x 15...
- Page 16 Over Current Protector 4A Strain Relief Strain Relief Plate Philips Screw M4 x 16 Updated December 2018 Charnwood Machinery Ltd, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU, England Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net...