Zamel EXTA LIFE ROM-22 Operation Manual

TWO-CHANNEL RECEIVER ROM-22
DESCRIPTION
A ROM-22 modular radio receiver is the fi-
nal element of EXTA LIFE system which allows
individual control of any two devices/circuits.
Two relays with switch contacts (NO/NC) with
maximum rated load 10A as outputs. This ena-
bles the user to control low voltage circuits (e.g.
12/24 VAC/DC) and high voltage circuits (230
VAC). The receiver is also good for remote ac-
tuation of other devices. You can also use it for
feeding control signals. The ROM-22 receiver is
also suitable for controlling solenoids in heating
systems. Thanks to bidirectional communica-
tion between the receiver and controller, you
can view each receiver channel's status at any
particular time on a mobile app. Also, the bidi-
rectional communication enables the operator
to change the specific parameters of the receiv-
er and add receivers remotely (i.e. without the
actual access to the receiver). Frame encryp-
tion algorithm ensures control safety. A receiver
installed outside a controller may be controlled
in parallel using the EXTA LIFE system's trans-
mitters. You can register more transmitters with
a receiver to enable independent control from
several locations. Configurable cable inputs in-
crease control functionalities. The receiver has
a built-in remote software update from a con-
troller. The product is designed for installing in
switch cabinets using a TH35 (DIN) bar. With
removable antenna to enable connecting an
external antenna.
FEATURES
● Rated supply voltage 230 V AC.
● Compatible with EXTA LIFE system control-
ler and transmitters.
● With 2 output channels (2 x potential-free
NO/NC switchable contacts).
● Two-way transmission with an indication of
each output status in the application.
● Programmable output status after supply
voltage loss.
● 2 programmable external inputs.
● For connecting monostable or bistable con-
nectors.
● 4 operating modes when working with trans-
mitters (activate/deactivate, bistable, mon-
ostable, time).
● 2 operating modes when working with con-
troller (activate/deactivate, time).
● Independently programmable time for radio
transmitters, external inputs and for control-
ler.
● Times assigned independently for each out-
put.
● Software can be updated remotely.
Zamel Sp. z o.o. hereby declares that the
ROM-22 radio equipment type conforms
to Directive 2014/53/EU.
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put the
used equipment together with other
waste.
ZAMEL Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04
www.zamel.com, e-mail: export@zamel.pl
TECHNICAL DATA
Rated power consumption
Transmitting/programming signalling Yes - green LED (STATUS)
Selected channel / channel status signalling Yes - red LEDs (CH1, CH2)
Maximum number of paired buttons 96 pairs (distributed into 2 channels)
Current channel status information Yes - in EXTA LIFE mobile application
Operation modes in co-operation with EXTA LIFE
Operation modes in co-operation with an EXTA LIFE
Number of external outputs 2
Compatible connectors* monostable (buttons), bistable
Operation modes for external inputs** Turn on/off, bistable, monostable, time
Time setpoint range*** 1 s–18 h
Number of output channels 2
Relay contact parameters 2 x NO/NC 16A / 250 VAC
(Selectable voltage-free contacts) 2 x 10 A / 250 VAC
Maximum outputs current-carrying capacity 2 x 10 A / 250 VAC
Number of termination points 10 (conductor cross-section up to 2.5 mm
Operating temperature range -10 to +55°C
Enclosure protection rating IP20
* Selection of switch possible only from the mobile app level coupled with the EFC-01 controller.
** Input operating mode selection depends on the type of selected coupler type.
*** Times are assigned independently to each channel of the receiver. The periods are programmed separately for
buttons operating in time mode, external inputs and for control from the app level.
APPEARANCE
Power terminals
Input terminals for cable control
(by default works with monostable connectors)
Transmit/receive signalling
/ status during programming operations
PROG. button - programming
Diodes for signalling currently selected
channel during programming / channel status
during normal operation
Output terminals (channel 1)
Output terminals (channel 2)
Rated supply voltage 230 VAC
Rated frequency 50 / 60 Hz
Standby: 0.65 W
One channel active: 1.3 W
Two channels active: 1.9 W
Transmission RF — ISM 868 MHz (868.50 MHz) band
Transmission mode duplex — 9600 bps
Maximum power 14 dBm (25 mW)
Encryption 128-bit key algorithm
Operating range max. 300 m in open areas
Turn on/off, bistable, monostable, time
system transmitters
Turn on, off, timer
controller
Enclosure mounting TH35 bar (DIN)
Dimensions 90 x 35 x 66 mm (double module)
Weight 0.13 kg
OPERATION MANUAL
)
2
Antenna socket
plik: ROM-22_inst_ext_gb | modyfikacja: 30.05.2018