Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Transmitter Solutions Manuals
  4. Extender
  5. Reign XRE-100
  6. Manual

Transmitter Solutions Reign XRE-100 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
The REIGN XRE-100 Relay Extender is a revolutionary product that
will make any dry contact wireless with no programming or
configuration whatsoever - it literally is a plug and play device.
WHAT'S INCLUDED
There are two pieces that complete the XRE-100.
The Reign XRE-100 - Relay Extender kit includes 2- XRE-100 units. These units are interchangeable and can be
paired in the field.
Transmitter Solutions refers to the XRE-100 installed at the peripheral device as the Node and the XRE-100
installed at the primary unit the Hub. This is only important during technical support and the wiring diagram.
HOW IT WORKS...
Congratulations on your purchase of the Transmitter Solutions XRE-100 Relay Extender System. It has been
designed with state-of-the-art radio technology to extend relay closures, switches, indicators, sensors, and any
other simple ON/OFF status inputs and outputs up to 40 miles line-of-sight.
If you ordered your XRE-100s together, they are factory paired. All that is required to get up and running is 12-24
Volts AC/DC power and the DRY input closures you want to extend.
If you would like to survey the range capability before install, simply provide power to both units and press the
PROG/TEST button alternately on each unit. Successful transmission and reception will be indicated on the
transmit and receive LEDs on each unit as described below.
R E L AY E X T E N D E R
R E I G N w i r e l e s s
t e c h n o l o g y
X R E – 1 0 0
v.8.29.18

Advertisement

loading

Summary of Contents for Transmitter Solutions Reign XRE-100

  • Page 1 WHAT’S INCLUDED There are two pieces that complete the XRE-100. The Reign XRE-100 - Relay Extender kit includes 2- XRE-100 units. These units are interchangeable and can be paired in the field. Transmitter Solutions refers to the XRE-100 installed at the peripheral device as the Node and the XRE-100 installed at the primary unit the Hub.

  • Page 3: Table Of Contents

    CONTENTS: 1. POWER DETAILS..................4 2.

  • Page 4: Power Details

    1. POWER DETAILS Each side of The XRE-100 (Hub and Node) need 1 amp of current draw to transmit at full power. IMPORTANT - XRE REQUIRES AT LEAST 1AMP POWER SUPPLY POWER INPUT: 1 AMP Minimum Power Input: 12 to 24 VOLTS AC/DC. Always follow polarity when DC Power is used. BATTERY INPUT: Battery Input: for 12 Volt Sealed Lead Acid (SLA) battery only.

  • Page 5: Led Indicators

    2. LED INDICATORS STATUS LEDs: RECEIVE - flashes GREEN momentarily when a valid radio transmission is received. TRANSMIT - flashes RED momentarily when the unit transmits a packet as a result of an Relay Input change event or handshake. STATUS/ PROG - flashes yellow patterns indicating status of the unit: pairing, error, etc.

  • Page 6: Relay Diagram And Wiring

    RELAY INPUTS Relay Inputs - The Reign XRE-100 comes with 2 relay inputs. Connect DRY closure from devices relay to be extended. A closure on RLY1 input will result in a closure on RLY1 (NC/COM/NO) of the paired XRE-100. A closure on RLY2/COM input will result in a closure on RLY2 (NC/COM/NO output) of the paired XRE-100.

  • Page 7: Alert Relays

    4. ALERT RELAYS ALERT INPUT (when DIP switch 2 is on) SUPERVISOR RESISTOR ALERT RELAY OUTPUT COLOR CODES Both RELAY 1 and RELAY 2 INPUTs are supervised when DIPSWITCH 2 in ON. Supervised inputs detect fault or tampering of inputs and send an ALERT RELAY activation to the opposite unit (Typically from the Node unit to the Base unit).

  • Page 8: Dip Switches

    5. DIP SWITCHES MODE SWITCHES SWITCH 1 – PROG (PAIR) – Pairing mode when ON and Normal operating mode when OFF SWITCH 2 – SUPERVISED INPUTS – Supervised inputs active when ON SWITCH 3 – COMMS LOSS BEACON – Pulses Alert Relay if ON, otherwise Relay is steady on SWITCH 4 –...

  • Page 9: Battery Backup

    6. BATTERY BACKUP 12 Volt Sealed Lead Acid (SLA) battery only. Solid GREEN LED indicates battery charging. Momentarily flashing GREEN LED indicates battery is charged and a trickle/conditioning charge is occurring. 7. PAIRING UNIT IN THE FIELD PAIRING Flip Dipswitch 1 to ON on both units. Press the PROG/TEST button on either unit NOTE: Observe the STATUS/PROG LED flashing.

  • Page 10: T R O U B L E S H O O T I N

    TROUBLESHOOTING XRE-100 units are not communicating: 1 - Check the Run LED. Normal operation will be orange LED flashing once a second. 2 - Press the red program button on the XRE-100. When pressed, the XRE-100 will send a radio test packet and the RED TRANSMIT LED will illuminate.
  • Page 11 “AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPER- TY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE.
  • Page 12 866.975.0101 • 866.975.0404 www.transmittersolutions.com...