Advertisement
Quick Links
Operation Manual
Airbrush
Airbrush-Spray Booth Compressor Suction Unit
Paint E420
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 16
http://www.wiltec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Summary of Contents for WilTec E420
- Page 1 Due to further developments illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 16 http://www.wiltec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of Wiltec Wil- danger Technik GmbH. The Wiltec Wildanger Technik GmbH assumes no liability for any errors in this user manual or for the connection diagram.
- Page 3 The user is responsible for complying with the location specific safety and mounting regula- tions (you can ask an electrician) • In case of device failure the repairs can be carried out only by an electrician or by the WilTec- repair service HINWEISE: •...
- Page 4 Cable winding device Right side plate Fan housing Flap door for cable Front worktop Light on/off-switch Upper cover plate Left front worktop Cable-rewinder button Cover plate Right front worktop Rubber bumpers © by WilTec Wildanger Technik GmbH Seite 19 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 5 100-240V, the wire can be extended to 2 meters. 3. Fold apart the device: open the front outer surface as upper cover plate of the spray booth. 4. Pull out the front worktop. 5. Unfold the worktop. © by WilTec Wildanger Technik GmbH Seite 20 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 6 9. The right and left sideplates can be placed vertically or taken out. By removing one of them a second chamber can be added and the working surface is doubled. © by WilTec Wildanger Technik GmbH Seite 21 http://www.wiltec.de http://www.aoyue.eu...
- Page 7 12. If you would like to use two chambers together, disas- semble the left sideplate of the unit on the right and the right sideplate of the unit on the left. After doing this the units can be jointed together. © by WilTec Wildanger Technik GmbH Seite 22 http://www.wiltec.de http://www.aoyue.eu...
- Page 8 Installation Light (optional) © by WilTec Wildanger Technik GmbH Seite 23 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 9 © by WilTec Wildanger Technik GmbH Seite 24 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 10 2. Unscrew the 4 screws from the protective grille on the back of the HS-E420 spray booth. Explore therefore you picture 1 on.
- Page 11 1 photo 2 photo 3 photo 4 Please pay attention to attach the plastic sleeve solidly to the ventilation grid. (You can see the correct installation on photo 3) © by WilTec Wildanger Technik GmbH Seite 26 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 12 • the device was stored for a long time under bad conditions • the device was exposed to heavy wear and tough conditions while transported. © by WilTec Wildanger Technik GmbH Seite 27 http://www.wiltec.de http://www.aoyue.eu http://www.teichtip.de...