Yaesu FT-7100M Technical Supplement page 12

Alignment
Internal System Alignment Routine
This uses a programmed routine in the transceiver
which simplifies many complex discrete component set-
tings and adjustments using digitally-controlled settings
via the front panel's buttons and LCD indications.
The examples below assume that the transceiver is to
be used in a 4-MHz-wide band (144-148 MHz). The facto-
ry-default settings for the FT-7100M assume a wider trans-
mit frequency range, so a "trick" must be used to set up
the frequencies correctly.
m In the Alignment mode, a special memory table
(see below) is temporarily established, providing
pre-set frequencies to be used in the alignment
process.
CH VHF
1 108.000 MHz 360.000 MHz
2 137.000 MHz 390.000 MHz
3 144.000 MHz 430.000 MHz
4 146.000 MHz 440.000 MHz
5 148.000 MHz 450.000 MHz
6 165.000 MHz 460.000 MHz
7 180.000 MHz 480.000 MHz
Note: For transceivers operating on 144-146 MHz,
use more appropriate frequencies, like
145.000/435.000 MHz (CH 4), 146.000/
440.000 MHz (CH 5).
m To enter the Alignment mode, turn the transceiver
off.
Now, short pins 1 and 6 of the MIC jack to Ground
(pin 4). While these two pins are shorted to
ground, press and hold in the HOME key while
turning the transceiver on.
m Disconnect the shorting of pins 1 and 6 of the MIC
jack to Ground; the transceiver is now in the
Alignment mode.
m In the Alignment mode, each Alignment Menu is
selected by the LOW (increase) and REV (de-
crease) keys; band change (VHF or UHF) is ac-
complished by the BAND key; and adjustment of
the setting is accomplished by rotating the Dial
knob.
m Once you have completed adjustment of each re-
quired Alignment Menu item, pressing the TONE
key will lock in that setting.
m If the alignment step requires that you "key the
transmitter," this may be accomplished by short-
ing pin 6 of the MIC jack to Ground.
m To save all settings and exit to normal operation,
press the V/M key.
12
UHF
UHF Transmitter Output
r Connect the wattmeter and dummy load to the
antenna jack.
r Enter the Alignment mode, then press the LOW
and/ or REV keys on the panel to select "
r Press the BAND key to select "
sary ( = parameter).
xxx
r Key the transmitter, and confirm that the output
power is more than 38 Watts.
r Press the LOW and/ or REV keys on the panel to
select " ." Press the BAND key to select "
PO HI
," if necessary (
xxx xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 35 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 35 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 35 watts (±0.5 W) on the wattmeter.
r Press the LOW and/ or REV keys on the panel to
select " ." Press the BAND key to select "
PO M 1
," if necessary (
xxx xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 20 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 20 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 20 watts (±0.5 W) on the wattmeter.
r Press the LOW and/ or REV keys on the panel to
select " ." Press the BAND key to select "
PO M 2
," if necessary (
xxx xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 10 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 10 watts (±0.5 W) on the wattmeter.
r Press the LOW key to select "
sary ( = parameter).
xxx
r Key the transmitter, and rotate the Dial knob so
as to achieve 10 watts (±0.5 W) on the wattmeter.
r Press the LOW and/ or REV keys on the panel to
select " ." Press the BAND key to select "
PO LO
," if necessary (
xxx xxx
POM AX
," if neces-
U4 xxx
= parameter).
," if neces-
U4 xxx
," if neces-
U5 xxx
= parameter).
," if neces-
U4 xxx
," if neces-
U5 xxx
= parameter).
," if neces-
U4 xxx
," if neces-
U5 xxx
= parameter).
."
U3
U3
U3
U3