Page 1
How to Connect MyPBX to NeoGate TE100 via SIP Trunking How to Connect MyPBX to NeoGate TE100 via SIP Trunking Version: 1.0 Yeastar Technology Co., Ltd. Date: January, 2014 http://www.yeastar.com 1/11...
1. Introduction ..........................3 2. Connect MyPBX to NeoGate TE100 ..................4 2.1 Create a Service Provider SIP Trunk on MyPBX ........4 2.2 Create a VoIP Trunk on NeoGate TE100 ..........5 2.3 Setup E1 trunk on NeoGate TE100 referring to the E1 trunk provider ..6 3.
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 1. Introduction This application note shows how to connect MyPBX to NeoGate TE100 via SIP trunking. Target: 1. Make outbound calls from MyPBX extension through the E1 trunks of NeoGate TE100 directly.
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 2. Connect MyPBX to NeoGate TE100 2.1 Create a Service Provider SIP Trunk on MyPBX Path: PBX→Trunks→VoIP Trunk→Add Service Provider Figure 2 Trunk Type: Service Provider Provider Name: NeoGateT100 Hostname/IP: 192.168.5.239...
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 2.2 Create a VoIP Trunk on NeoGate TE100 Path: Gateway→VoIP Settings→VoIP Trunk→Add VoIP Trunk Choose "Service Provider" mode, and fill in MyPBX IP address. Figure 4 Trunk Type: Service Provider...
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 2.3 Setup E1 trunk on NeoGate TE100 referring to the E1 trunk provider Figure 6 After save and apply changes, please check the E1 trunk status on Status -> System Status ->...
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 3. Outgoing Call from MyPBX Extensions through E1 Figure 8 3.1 Create an Outbound Route on MyPBX Path: PBX→ Outbound call control → outbound routes Choose the VoIP trunk "NeoGateTE100" and set the rule for the outbound as the picture shows, which allows users to dial out any number out.
How to Connect MyPBX to NeoGate TE100 via SIP Trunking Figure 9 3.2 Create Route on NeoGate TE100 Path: GatewayRoutes SettingsRoutes List Figure 10 http://www.yeastar.com 8/11...
How to Connect MyPBX to NeoGate TE100 via SIP Trunking Simple Mode: Call Comes in From: ServiceProvider-MyPBX. Send Call Through: Trunk—E1Trunk1. 3.3 Setup DOD for MyPBX Extensions on MyPBX Figure 11 For example, we set extension 301 as DOD number 5551001.When you use extension 301 to make outgoing call through NeoGate TE100, callee will see the caller ID number 5551001.
How to Connect MyPBX to NeoGate TE100 via SIP Trunking 4. Incoming Call from E1 to MyPBX Figure 12 4.1 Create ‘FromTEToMyPBX’ Route on NeoGate TE100 Path: Gateway→Routes Settings→Routes List Figure 13 Simple Mode: Call Comes in From: Trunk—E1Trunk1. Send Call Through: ServiceProvider-MyPBX.
5551001 (which is same to the E1 trunk external number) Set Destination: After saving the settings, you can dial the E1 DID number 5551001 from the mobile phone, the call will be routed to the extension 301 on MyPBX. <End> http://www.yeastar.com...