Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vollrath Stoelting F212
Summary of Contents for Vollrath Stoelting F212
- Page 1 Model F212 OPERATORS MANUAL Manual No. 513675 Rev.0...
- Page 3 This manual provides basic information about the machine. Instructions and suggestions are given covering its operation and care. The illustrations and specifi cations are not binding in detail. We reserve the right to make changes to the machine without notice, and without incurring any obligation to modify or pro- vide new parts for machines built prior to date of change.
-
Page 4: Safety Information
A Few Words About Safety Safety Information Safety Alert Symbol: Read and understand the entire manual before This symbol Indicates danger, warning or caution. operating or maintaining Stoelting equipment. Attention is required in order to avoid serious per- sonal injury. The message that follows the symbol This manual provides the operator with information contains important information about safety. -
Page 5: Table Of Contents
TABLE OF CONTENTS Section Description Page Description and Specifi cations Description ....................1 Specifi cations ..................... 2 Installation Instructions Safety Precautions ..................3 Shipment and Transit .................. 3 Machine Installation ..................3 Initial Set-Up and Operation Operator’s Safety Precautions ..............5 Operating Controls and Indicators ............. -
Page 7: Description And Specifi Cations
SECTION 1 DESCRIPTION AND SPECIFICATIONS 1.1 DESCRIPTION The Stoelting F212 fl oor model machine is gravity fed. The machine is equipped with fully automatic controls to provide a uniform product. The machine will operate with almost any type of shake mix. This manual is designed to help qualifi... -
Page 8: Specifi Cations
1.2 SPECIFICATIONS F212 Dimensions Machine with crate width 18-1/4’’ (46,4 cm) 25’’ (63,5 cm) height 64-1/2’’ (163,8 cm) 66’’ (167,6 cm) depth 33’’ (83,8 cm) 51’’ (129,5 cm) Weight 315 lbs (142,8 kg) 410 lbs (185,9 kg) Electrical 1 Phase, 208-240 VAC, 60Hz running amps connection type NEMA6-20P power cord provided... -
Page 9: Installation Instructions
SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the machine until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. Take notice of all warning labels on the machine. The la- bels have been put there to help maintain a safe working environment. - Page 10 Operators Manual #513675 F212 Model Machines...
-
Page 11: Operator's Safety Precautions
SECTION 3 OPERATION 3.1 OPERATOR’S SAFETY PRECAUTIONS 3.2 OPERATING CONTROLS AND INDICATORS SAFE OPERATION IS NO ACCIDENT; observe these Before operating the machine, it is required that the op- rules: erator know the function of each operating control. Refer to Figure 3-1 for the location of the operating controls on Know the machine. -
Page 12: Assembly Of Machine
CLEAN-OFF-ON Switch 3.3 ASSEMBLY OF MACHINE The CLEAN-OFF-ON switch is used to supply All parts should be cleaned, sanitized and allowed to air power to the control circuit. When the switch dry before assembling. is in the OFF (middle) position, power will not To assemble the machine parts, refer to the following steps: be supplied to the control board or refrigeration NOTE... -
Page 13: Sanitizing
Look for the proper seal between the freezing Mix sanitizer according to manufacturer’s instructions to cylinder, front door o-ring, and front door. provide a 100 parts per million (ppm) strength solution and check the solution with chlorine test strips. Allow Install the mix inlet regulator into the hopper. -
Page 14: Freeze Down And Operation
3.5 FREEZE DOWN AND OPERATION 3.7 REMOVING MIX FROM MACHINE This section covers the recommended operating proce- To remove the mix from the machine, refer to the follow- dures for the safe operation of the machine. ing steps: Sanitize just prior to use. Pull the mix inlet regulator straight up and remove it from the hopper. -
Page 15: Cleaning And Sanitizing The Machine Parts
Prepare sanitizing solution according to manufacturer’s instructions to provide a 100 ppm strength solution. Mix the sanitizer in quantities of no less than 2 gallons of 90° to 110°F (32° to 43°C) water. Check the strength of the sanitizing solution. Use a chlorine test strip and color chart to make sure the solution has 100 ppm. -
Page 16: Preventive Maintenance
3.13 PREVENTIVE MAINTENANCE E. SEMI-ANNUALLY Disconnect the machine from the power source. A. DAILY Use a Burroughs Belt Tension Gauge to set the The exterior should be kept clean at all times to tension for the drive belt. Set the belt tension to preserve the luster of the stainless steel. -
Page 17: Troubleshooting
SECTION 4 TROUBLESHOOTING 4.1 LIGHT INDICATORS The machine has two lights that will alert the user if a problem occurs: an ADD MIX light and a Diagnostic Light. The ADD MIX light will fl ash to alert the operator to a low mix condition. It does so by monitoring the mix level in the hopper. - Page 18 4.2 TROUBLESHOOTING - CONTINUED PROBLEM POSSIBLE CAUSE REMEDY 1 Temperature setting too warm. 1 Adjust the Temperature Adjustment Screw (Section 3.2) 2 No vent space for free fl ow of cooling 2 A minimum of 3” of air space at the sides. air.
-
Page 19: Replacement Parts
SECTION 5 REPLACEMENT PARTS 5.1 BRUSHES, DECALS, AND LUBRICATION Part Description Quantity C-1000-26C Decal - Made In USA 208135 Brush - 4” X 8” X 16” (Barrel) 208380 Brush - 1/4” X 3” X 14” 208401 Brush - 1” X 3” X 10” 208410 Brush - 1-1/2”... -
Page 20: Auger Shaft And Faceplate Parts
5.2 AUGER SHAFT AND FACEPLATE PARTS 666786 4177749 624678 149002 162155 625314 336589 3177738 624614 Part Description Quantity 149002 Bushing - Front Auger Support 162155 Blade - Scraper 336589 Door - Front 482019 Knob - Front Door (Black) 624614-5 O-Ring - Spigot (5 Pack) 624678-5 O-Ring - Rear Seal - Black (5 Pack) 625314... -
Page 21: Hopper Parts
5.3 HOPPER PARTS 2202074 624607 314187 232086 744608 417010 2204302 221164 744287 Part Description Quantity 221164 Bushing - Agitator Bottom Center Post 232086 Cap - Drive 314187 Cover - Hopper 417010 Grid - Drip Tray 624607 O-Ring - Mix Inlet 744287 Tray - Drip 744608... - Page 22 Operators Manual #513675 F212 Model Machines...
- Page 23 DOMESTIC WARRANTY (Including Mexico) SOFT SERVE / SHAKE EQUIPMENT 1. Scope: PW Stoelting, L.L.C. (“Stoelting”) warrants to the first user (the “Buyer”) that the freezing cylinders, hoppers, compressors, drive motors, speed reducers, and augers of Stoelting soft serve / shake equipment will be free from defects in materials and workmanship under normal use and proper maintenance appearing within five (5) years, and that all other components of such equipment manufactured by Stoelting will be free from defects in material and workmanship under normal use...
Need help?
Do you have a question about the Stoelting F212 and is the answer not in the manual?
Questions and answers