Subscribe to Our Youtube Channel
Related Manuals for IKA T25 easy clean digital
Summary of Contents for IKA T25 easy clean digital
- Page 1 20000017329a T25 easy clean digital/control_072018 IKA T25 easy clean digital IKA T25 easy clean control Operating instructions...
-
Page 2: Device Setup/Dangerous Parts
Device setup/Dangerous parts Device setup Item Designation Operator panel and display Turning knob Dispersion tool USB port Stand Extension arm Cross sleeve Power switch Strap clamp Fig. 1 Dangerous parts Fig. 2... -
Page 3: Table Of Contents
Directive: 2014/53/EU Standards: EN 60950-1, EN 300328, EN 301489-1, EN 301489-17 A copy of the complete EU Declaration of Conformity can be requested at sales@ika.com. Explication of warning symbols indicates a hazardous situation which, if not avoided, will result in death or serious injury. -
Page 4: Safety Instructions
The dispersing tool and the cou- Device setup: WARNING pling flange can become hot during The power switch of the IKA device DANGER the operation. must be accessed immediately, di- rectly and without risk at any time. If a dispersion tool is not inserted into the drive flange as... -
Page 5: Intended Use
Do not use damaged components. direct danger. • Only dispersion tool approved by IKA may be used. • Safe operation is only guaranteed with the accessories de- scribed in the ”Accessories” chapter. -
Page 6: Unpacking
Unpacking: Delivery scope: - Unpack the device carefully. - IKA T 25 easy clean digital or IKA T 25 easy clean control - Any damage should be notified immediately to the shipping - Extension arm agent (post office, railway network or logistics company). -
Page 7: Securing
Securing Securing the extension arm to the disperser: Securing the dispersion tool: Drive unit Disperser Hexagon socket Turning knob offset screw key Hexagonal socket screw Dispersion tool Extension arm Fig. 6 Open the turning knob so that the thread does not protrude Fig. -
Page 8: Operator Panel And Display
Operator panel and display T25 easy clean digital: Item Designation Function "Speed" display: Display the "Speed" value (x 1000 rpm). "Timer/Counter" display: Indicate the "Timer/Counter" value. "h:min" indicator: Indicate the "Timer" or "Counter" is in hour/minute [h:min] mode. "Timer" indicator: Indicate the "Timer"... - Page 9 T25 easy clean control: Item Designation Function easy clean "Speed" display: Display the "Speed" value (x 1000 rpm). "Timer/Counter" display: Indicate the "Timer/Counter" value. Indicate the remaining time to maintenance. When device is controlled by a WiCo, the dis- play show rC ( "h:min"...
-
Page 10: Commissioning And Operating
Commissioning and operating Refer to the operating instructions for the filling level of the Check whether the voltage given on the type plate corre- medium and the immersion depth into the dispersion tool sponds to the available power voltage. used. The socket used must be earthed (fitted If a dispersion tool is not inserted into the drive flange as far with earth contact). - Page 11 When the tool maintenance time reach 0, the device will not stop, but we recommend a maintenance of the tool as soon as possible. After the maintenance in a IKA service workshop the maintenance time will be reset from the service team. In all other cases it is possible to reset the maintenance time with the device.
-
Page 12: Interfaces And Outputs
1.1). The NAMUR commands and the additional specific IKA commands commissioning serve only as low level commands for communication between the tube driver and the PC. With a suitable terminal or communications program these com- mands can be transmitted directly to the tube driver. -
Page 13: Accessories
S 25 EC - T - C - 18G - ST Stainless steel Abbreviations: (S 25 EC only suitable for T25 easy clean digital or S 25: consistent with all dispersing units T 25... T25 easy clean control. Full functionality of the S 25 EC-T PTFE bearing ... -
Page 14: Warning Message
Warning message Any malfunction during operation may be identified by an warning message on the display. Proceed as follows in such cases: Warning code Cause Effect Solution The dispersion tool is not secured motor off - Secure the dispersion tool properly. properly. -
Page 15: Maintenance And Cleaning
For repair, please request the “Decontamination Certif- Construction material water containing tenside/isopropyl alcohol icate” form IKA or use the download printout of it from Cosmetics water containing tenside/isopropyl alcohol IKA website: www.ika.com. Foodstuff water containing tenside... -
Page 16: Technical Data
2000 Subject to technical changes! Warranty In accordance with IKA warranty conditions, the warranty The warranty does not cover worn out parts, nor does it period is 24 months. For claims under the warranty please apply to faults resulting from improper use, insufficient care contact your local dealer. - Page 17 IKA-Werke GmbH & Co.KG Janke & Kunkel-Str. 10 D-79219 Staufen Tel. +49 7633 831-0 Fax +49 7633 831-98 sales@ika.de www.ika.com...
Need help?
Do you have a question about the T25 easy clean digital and is the answer not in the manual?
Questions and answers