Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mac allister Titan TTK550LWM
Summary of Contents for Mac allister Titan TTK550LWM
- Page 1 TTK550LWM Rider MM66 RIDE-ON LAWNMOWER WITH SEATED OPERATOR OWNER’S MANUAL WARNING! Read this manual carefully before using the machine. Supported by For all your Warranty, Parts and Service needs 0800 121 6585 www.servicelink.org.uk...
- Page 2 Please retain this handbook in case you need to refer to any of the information in the future. Your MAC ALLISTER Ride On Lawnmower comes with a 1 year guarantee, so should it develop a fault within this period contact the Service Link helpline on 0800 121 6585.
- Page 3 TTK550LWM by TITAN Let’s get started These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting started... Your product Technical data Accessory list Safety instructions Unpacking and assembly more detail... Operation Care and maintenance Troubleshooting...
-
Page 4: Your Product
TTK550LWM by TITAN Your product Your product IDENTIFICATION OF THE MACHINE The identification label located under the seat Type has the essential data of each machine. kW - /min The serial number (6) must be quoted Art.N. when you require technical assistance or spare parts. -
Page 5: Technical Data
TTK550LWM by TITAN Technical and legal informations Technical data Electrical system ......12 V Mechanical transmission Battery .......... 7.2 Ah Tyres 11”-13” Front tyres ......11 x 4.00-4” Forward speed (approximate) or ........13 x 5.00-6” in Forward gear ..1.4 - 5.5 km/h Rear tyres ...... -
Page 6: Accessory List
TTK550LWM by TITAN Accessory list Accessory list (Available separately) 1. KIT FOR “MULCHING” 2. CLOTH COVER It chops the grass cuttings finely and Protects the machine from dust when leaves them on the lawn, instead of col- not in use. lecting them in the grass catcher. -
Page 7: Safety Instructions
TTK550LWM by TITAN Safety instructions Safety instructions SAFETY DECALS Your machine should be used with due care and attention. Therefore, labels have been placed on the machine to remind you pictorially of the main precautions to take during use. These labels are to be considered an integral part of the machine. If a label should fall off or become illegible, contact your Retailer to replace it. -
Page 8: General Safety
TTK550LWM by TITAN Safety instructions General safety DESCRIPTION OF THE MACHINE AND ITS RANGE OF USE This machine is a garden tool and precisely a ride-on lawnmower with seated operator. The machine is equipped with an engine which drives a cutting unit protected by a casing, as well as a transmission unit that moves the machine. -
Page 9: Additional Safety
TTK550LWM by TITAN Safety instructions Additional safety HOW TO READ THE MANUAL The manual describes several machine models that can mainly differ in: – type of transmission: with mechanical gear-change or with hydrostatic continuous speed adjustment. The models with hydrostatic transmission are identified by the word “HY- DRO”... -
Page 10: Preliminary Operations
TTK550LWM by TITAN Safety instructions 4) Never use the machine if the user is tired or unwell, or has taken medicine, drugs, alco- hol or any substances which may slow his reflexes and compromise his judgement. 5) Bear in mind that the operator or user is responsible for accidents or unexpected events occurring to other people or their property. -
Page 11: During Use
TTK550LWM by TITAN Safety instructions C) DURING USE 1) Do not operate the engine in a confined space where dangerous carbon monoxide fumes can develop. All ignition operations have to be effected in an open or well-ventilated area. Always remember that exhaust fumes are toxic. 2) Work only in daylight or with good artificial light in good visibility conditions. -
Page 12: Maintenance And Storage
TTK550LWM by TITAN Safety instructions 24) Do not touch the engine parts as they get very hot when running. Danger of burns. 25) Disengage the cutting means or power socket, put in neutral and engage the parking brake, turn off the engine and remove the ignition key (checking that all moving parts are completely stationary): –... -
Page 13: Environmental Protection
TTK550LWM by TITAN Safety instructions 6) Check that the cutting means screws are properly tightened on a regular basis. 7) Wear work gloves when handling, disassembling and reassembling all cutting means. 8) Keep the cutting means well balanced during sharpening. All works on the cutting means (disassembly, sharpening, balancing, reassembly and/or replacing) are demanding jobs that require special skills as well as special tools. -
Page 14: Before You Start
TTK550LWM by TITAN Before you start Unpacking and assembly For storage and transport purposes, some components of the machine are not installed in the factory and have to be assembled after unpacking. Follow the instructions below. IMPORTANT The machine is supplied without engine oil or fuel. Before starting up the en- gine, fill with oil and fuel following the instructions given in the engine manual. - Page 15 TTK550LWM by TITAN Before you start FITTING THE REAR PLATE • Use equipment marked “A”. Apply plates (1) to the two supporting brackets (2) and (3), as shown in the figure. Screw (4) the two brackets (2) and (3) to the chassis supports, taking care they are in the correct right and left positions.
-
Page 16: Fitting The Seat
TTK550LWM by TITAN Before you start Fit the dashboard cover (5) making sure all fastenings click into their respective hous- ings correctly. Fit the steering wheel (6) onto the caster (3) with all the spokes directed towards the seat. Fit the steering wheel fastening it with the screws (7a/b/c) supplied, in the indicated order. -
Page 17: Connecting The Battery
TTK550LWM by TITAN Before you start CONNECTING THE BATTERY The battery (1) is located under the seat and can be reached by moving the cover (2). Connect the battery connector (3) to the ma- chine connector (4) and arrange the wire (5) so that it is held firmly in place (7). - Page 18 TTK550LWM by TITAN Before you start FITTING THE “MULCHING” ATTACHMENT (if provided) • Use equipment marked “E”. Fit the handle (1) on the deflector cap (2) using the pin (3) pushing it to the end with a hammer. Insert an end of the spring (4) in the deflector cap (2) opening and fasten it with the pin (5) in- serted in the specific deflector cap (2) seat (6).
- Page 19 TTK550LWM by TITAN more detail... Operation Care and maintenance Troubleshooting Service Link EC declaration of conformity...
-
Page 20: Steering Wheel
TTK550LWM by TITAN 1. STEERING WHEEL Turns the front wheels. 2. PARKING BRAKE This lever stops the machine from moving when it has been parked. There are two positions: «A» = Brake disengaged «B» = Brake engaged – The brake is applied by pressing the pedal right down (11 or 21) and moving the lever to position «B». - Page 21 TTK550LWM by TITAN Operation – In disengaging the cutting means (Pos. «A»), a brake is simultaneously activated which stops their rotation within five seconds. 4. CUTTING HEIGHT ADJUSTMENT LEVER This lever has several positions so the cut can be regulated at various heights.
-
Page 22: Clutch / Brake Pedal
TTK550LWM by TITAN Operation Mechanical transmission 11. CLUTCH / BRAKE PEDAL This pedal has two functions: during the first part of its travel it acts as a clutch, engaging and disengaging drive to the wheels, and in the second part it acts as a brake on the rear wheels. - Page 23 TTK550LWM by TITAN Operation 23. HYDROSTATIC TRANSMISSION DISENGAGEMENT LEVER This lever has two positions as shown on the label: «A» = Transmission engaged: for all uses, when moving and during cutting; «B» = Transmission disengaged: this makes it much eas- ier to move the machine by hand, with the engine turned off.
-
Page 24: Safety Recommendations
TTK550LWM by TITAN Operation SAFETY RECOMMENDATIONS WARNING! This machine must not be used on slopes steeper than 10° (17%) Using on Slopes). IMPORTANT All the references relating to the positions of controls are described from page 20 to page 23. WHY THE SAFETY DEVICES CUT IN The safety devices work in two ways: –... -
Page 25: Tyre Pressure
TTK550LWM by TITAN Operation Tyre pressure Having the right tyre pressure is the main condition for ensuring that the cutting-means as- sembly is horizontal and mows evenly. Unscrew the valve caps and connect a compressed air line with a gauge to the valves and adjust the pressure to the indicated values. - Page 26 TTK550LWM by TITAN Operation Preparing the machine and fitting the exit guards (grass catcher or side discharge chute) NOTE This machine lets you mow lawns in different ways, according to the fitted attach- ments. The attachments mentioned here may be part of the original equipment or may be purchased afterwards.
-
Page 27: Using The Machine
TTK550LWM by TITAN Operation Checking machine safety and efficiency 1. Check that the safety devices function as described ( Why the safety devices cut in). 2. Check that the brake is in perfect working order. 3. Do not start mowing if the cutting means vibrate or if you are unsure whether they are sharp enough. - Page 28 TTK550LWM by TITAN Operation – bring the cutting-means assembly to the highest position (position «7»); – put the accelerator control between the «SLOW» and «FAST» positions. Mechanical transmission Push the pedal down as far as possible ( page 22, n. 11) and move the gear change lever into 1st gear ( page 22, n.
- Page 29 TTK550LWM by TITAN Operation Mechanical transmission Press the pedal until the machine stops and then switch into reverse by shifting the le- ver sideways and into position «R» ( page 22, n. 12). Gradually release the pedal to engage the clutch and then begin moving in reverse. Hydrostatic transmission: When the machine is stopped, start the reverse movement by pressing the drive pedal in the «R»...
-
Page 30: Emptying The Grass Catcher
TTK550LWM by TITAN Operation Emptying the grass catcher NOTE The emptying of the grass catcher can only be done with the cutting means disengaged, otherwise the engine stops. The grass catcher is full when the grass cuttings remain on the lawn. If you continue mowing with the grass catcher full, it may block the collector channel. -
Page 31: Cleaning The Machine
TTK550LWM by TITAN Operation Cleaning the machine After each mowing session, clean the outside of the machine, empty the grass catcher and shake it to remove residual grass and earth. Clean the plastic parts of the body with a damp sponge using water and detergent, taking care not to wet the engine, the electrical parts or the electronic circuit board located under the seat. -
Page 32: Using On Slopes
TTK550LWM by TITAN Operation Storage and inactivity for long periods If you intend not to use the machine for a long period (more than 1 month), disconnect the battery cables and follow the instructions in the engine instruction manual. Close the fuel stopcock (1). Remove the clamp (2) using pliers, reconnect the tube (3) and empty the tank collecting all the fuel in a suitable container. -
Page 33: Suggestions For Maintaining A Nice Lawn
TTK550LWM by TITAN Operation SUGGESTIONS FOR MAINTAINING A NICE LAWN 1. To keep a lawn green and soft with a good appearance, it should be cut regularly without damaging the grass. A lawn can be composed of different types of grass. If the lawn is cut frequently, grass and roots grow more vigorously, forming a solid grassy bed. -
Page 34: Care And Maintenance
TTK550LWM by TITAN Care and maintenance Care and maintenance SAFETY RECOMMENDATIONS WARNING! You must go to a specialized Service Centre or contact your Dealer if the following are malfunctioning: – the brake; – the cutting means engage and disengage functions, –... - Page 35 TTK550LWM by TITAN Care and maintenance Engine Follow all the instructions in the engine manual. The engine oil is emptied using a syringe (2) (attachment on request) suited for that use, after unscrewing the cap (1). Fit a small pipe (3) of the right size and at least 400mm long on to the syringe (2) ;...
-
Page 36: Interventions On The Machine
TTK550LWM by TITAN Care and maintenance INTERVENTIONS ON THE MACHINE Aligning the cutting-means assembly The cutting-means assembly should be properly adjusted to obtain an evenly mown lawn. If mowing is uneven, check the tyre pressure. If this is not sufficient to achieve an even cut, please contact your Dealer to adjust the alignment of the cutting- means assembly. - Page 37 TTK550LWM by TITAN Care and maintenance IMPORTANT A blown fuse must always be replaced by one of the same type and ampere rating, and never with one of another rating. If you cannot find out why the fuse has blown, consult a Licensed Service Centre. Removing, replacing and reassembling of cutting means WARNING! Always wear strong protective gloves to handle the cutting means.
-
Page 38: Troubleshooting
TTK550LWM by TITAN Troubleshooting Troubleshooting PROBLEM LIKELY CAUSE SOLUTIONS 1. With the key on Electronic circuit board blocked Turn the ignition key to «STOP» «START» the starter due to: position and look for the cause of motor does not run. the problem: –... - Page 39 TTK550LWM by TITAN Troubleshooting PROBLEM LIKELY CAUSE SOLUTIONS 7. Uneven mowing – cutting-means assembly is not – check the tyre pressure and poor grass parallel to the ground page 25) collection – reinstate the alignment of the cutting-means assembly in relation to the ground page 36) –...
- Page 40 TTK550LWM by TITAN Service Link Service Link This product is supported by Service Link. If you have been unable to find the information you require above please call the Service Link helpline. Here you will find 1-2-1 help and advice from HELPLINE garden machinery repair specialists.
-
Page 41: Ec Declaration Of Conformity
TTK550LWM by TITAN EC Declaration of conformity DICHIARAZIONE CE DI CONFORMITÁ (Istruzioni Originali) FR (Traduction de la notice originale) EN (Translation of the original instruction) DE (Übersetzung der Originalbetriebsanleitung) (Direttiva Macchine 2006/42/CE, Allegato II, parte A) Déclaration CE de Conformité EC Declaration of Conformity EG-Konformitätserklärung (Directive Machines 2006/42/CE, Annexe II, partie... -
Page 44: Identification Of The Machine
As soon as you have purchased the machine, write the machine identification data (3 - 5 - 6) found on the identification label in the spaces provided ( IDENTIFICATION OF THE MACHINE). ST. S.p.A. Via del Lavoro, 6 31033 Castelfranco Veneto (TV) ITALY 171505972/2...
Need help?
Do you have a question about the Titan TTK550LWM and is the answer not in the manual?
Questions and answers